Get help and assistance with your Sonos system

Hello everyone,Lately, I've noticed the volume level seems lower when integrating Sonos and Spotify. I've tested this on several Era 100s, Fives, and Sonos Ones, and I find myself needing to increase the volume significantly compared to last week. Do you know if there have been any recent changes to the Spotify integration volume? This occurs whether using Spotify Connect and the Sonos app. Do you have the same feeling?

Good day,I have two Sonos Era 100. They both work fine individually when i connected them to my computer via bluetooth. However, when i paired them up as a stereo pair, the speaker that isn't connect to the PC keeps breaking up, and the one that is connected works perfectly. Same thing happens when i connect my Samsung phone to the stereo pair. I have also tried connecting Bluetooth to the other speaker and the problem persist in a reverse manner. The breaking is extremely frequent, about half or one full second every ten seconds. When i off the wifi the breaking is way worst.The two speakers are on either side of my 27 inch monitor and the computer is on the left side under the table. Bluetooth from the computer is a Bluetooth 5.0 dongle from TP Link. Mesh router is about 5.5meters (18 feet)  unblocked from my PC.I have no issues when streaming spotify from my phone.I have tried all of solutions i can find on the web, including power cycling on the speak

I have a lg Evo G5 with everything set on auto on sound settings and HDMI ARC.The Sonos App shows Dolby multichannel PCM 5.1 on a Amazon prime.Should it show Dolby atmos?Is there a test to make sure I have TV/arc ultra set-up properly?

I wanted to gauge from the community as to whether or not people are experiencing bad sound quality through their arc ultra speakers as I have had two units and both have produced a slightly distorted/fuzzy sound specifically from the right side of the speaker. I don’t know if it’s bad luck or not but wanted to check with others to see if they’re also experiencing this and what they did to fix it? My arc ultra is connected to my Samsung tv through the eARC port with the cable provided and use my Apple TV 4K Gen 1 to watch content. The fuzzy noise is present when watching any kind of media through the Apple TV as well as when I’m streaming music through the Sonos app and even when adding the product to my system through the chime it plays as well as during the trueplay tuning. I have even changed the settings on the Samsung tv such that sound is output via pass through rather than automaticAny help would be much appreciated, I will try get the product

i have a arc a gen 4 sub and pair of play ones.i cant get the gen 4 sub to pair what do i do

After the latest Iphone update “Your Sources” no longer show up as an option in the Sonos app.  This is how we connect back to the TV once we are finished listening to music.  How do I add “Your Sources” back to the Sonos App?

Since upgrading to Windows 11 my Sonos system was no longer recognising my Music Library.Having viewed other support advice, I have set my Wifi network to Private but it still doesn’t work.I removed the existing library and am now trying to add it back but am getting nowhere.I go to Music Library settings and click Add to add a new folder. I then click on browse and choose my music folder (on the same laptop) and then click on Next to add it.This brings up a window headed ‘Adjust file sharing settings’ saying the setup assistant needs to adjust the following 1) add sonos library service to firewall exceptions list and 2) set Windows sleep settings to Never. I click on Next to do this and then get a window asking if I want to allow Sonos to make changes. I click on Yes and it just takes me back to the window to choose my music folder. Nothing has been added.NB I have separately added the Sonos library service to my firewall exceptions list and the S

I’ve just spent over an hour on the phone with Sonos Support, who, whilst extremely helpful, have been unable to fix this problem, so a last-ditch attempt is asking the community!3 months ago, I bought the following system:-2 x Era 1001 x Sub MiniAt first, it appeared to be working well, and I successfully paired all three speakers.  However, one of the Era 100’s started to disconnect occasionally.  It has now totally disconnected and is missing from the Sonos app / system.Here’s what I have tried so far:-Reset router Reset access points Reset Sonos speakers Switched off firewall Switched off VPNs Changed access point (from Unifi to Xytel) Hard reset the problematic Era 100 Hard wired the problematic Era 100 (with a USB-C to Ethernet adapter). Tried both iPhone and iPad iOS appsWhen I do a hard reset of the speaker, the Sonos app

SetupSpeakers - Arc with Sub and two play1 surround.latest iOS app the surrounds and sub are disconnected. I cannot remove them in app, When I removed the sub it crashed app (twice).I have now factory reset arc and sub then:1. have added arc (working)2. have added the sub (working)3. two play 1 speakers on system(working)ThenPrompted in app to Add sub to arc… All ok. Connected and success sound.Prompted in app to Add surround, select both speakers, test sounds, select the position…. All ok. Connected and then plays success sounds. Go back into the app… All home theater broken again.  Help? 

Is anyone in Sonos support aware of the following intermittent AirPlay bug that has been introduced as of iOS 26.2? There appear to be quite a few people experiencing it, including me on two independent, physically disjoint Sonos systems.While it is likely to be a bug introduced on the Apple side of the connection, with networking you never know for sure, so perhaps Sonos support should reach out to Apple about it.AirPlay Bug Report on RedditDave Ings

HiI have a controller CR200 that I can’t factory reset. I have already done tries stepsTake out the battery and replace it and placed in the cradle - Take out and replace the battery and placed in the cradle while I presse Mute + Home button and slide it down into the cradle, stille pressing the buttons.The controller start up every time, and start looking for a Sonos product. I can see the SETTING in the bottom of the screen but noting happens when I press the button Can anyone tell me how I make a factory reset on it ? Others ideas is also very welcome to fix this ola guy Regards Reidl 

I have a Pro-ject turntable connected to an Era100 stereo pair + Sub mini via the OEM Sonos USB adapter. Audio is passed from the turntable to my setup just fine. The problem: the setting for Line In Source Level no longer has any effect - I can change it from Level 1 → Level 10 with no audible effect. Also, if I change it to anything other than Level 1, if I quit the app then reopen it, the Source Level is back on Level 1. No other Level settings “sticks”. Prior to this, I was using the same turntable and adapter to connect to a Move 2 (months ago). The Source Level control worked just fine then (I had to keep it set to Level 7). Now, several app updates and firmware updates later, it’s not working - I’m not sure when it stopped working.A few people are reporting the same issue on Reddit. Is this a known issue?

i have the sonos arc and i put in a home theater setup. i have no idea where to put the sonos arc because there’s cabinetry behind it that is not perfectly symmetrical. where would you put the sonos arc in this setup? is there a way to hang it from the ceiling? can i place it on the cabinets but off center? the seating is on the left already.

Some of my Sonos speakers don’t show volume sliders in the app and it’s driving me crazy. Audio plays fine and grouping works, but I can’t control volume for some of my speakers. It always ends up that one volume slider remains, while the rest disappear. And this on al my devices, they even show the same volume sliders grayed out.What I’ve already tried: All speakers are on the same 5GHz network, same AP Disabled AP isolation, client isolation - no change Turned off WiFi band steering - no change Played with IGMP snooping settings on my switches - still broken No multicast rate limiting configured Speakers have static IPs assigned Wireshark shows that all speakers are communicating, on both IGMP and SSDP. Even the ones that don’t show the volume sliders. The only thing that works is restarting my router, but even then the problem always returns. Running TP

Is anyone else having problems with Deezer in Australia attaching the service to their Sonos account ?

I’ve seen various posts stating that the Sonos Ace ANC exhibits various popping or crackling effects as a result of nearby high-pitched sounds like knives, forks and other cutlery banging together.Examples:https://en.community.sonos.com/headphones-229145/sonos-ace-crackling-static-popping-with-certain-sounds-issue-with-anc-6927617 https://en.community.sonos.com/headphones-229146/sonos-ace-feedback-over-bumps-6897038Has this been fixed?I understand the newer Firmware has greatly improved the ANC, but I can’t find a clear conclusion on this topic.

First time poster, so not really sure if I’m posting in the right area to share what seems like a bug, but with my Nintendo Switch 2, Sonos Arc + surrounds + Sub mini, and LG C5, running the NS2 test output plays the SW test tone too audibly (IMO) through the Arc. Sonos app correctly shows Multichannel PCM 5.1 and all the other test tones are appropriate, but it seems like the subwoofer audio just isn’t playing from where it should be.