Advanced setups

I’m keen to set up this situation:   Sonos Amp 1 to Sonos Outdoor Pair A and Sonos Pair B Sonos Amp 2 to Sonos Architectural In-Ceiling Speakers 3 in Room A and 3 in Room B   In order to switch Outdoor Pair A/B and In-Ceiling Room Room A/B I was hoping to hook the Sonos Amps to this McClelland 6 way Speaker Selector: https://www.radioparts.com.au/product/39894210/ss26v-6-way-premium-speaker-selector-volume-control-150w-totalrms#.Xp1zaOQmLDs   Is this doable? 

Is it possible to disable the feature of sonosnet that carries non-sonos traffic to an ethernet device connected to a remote speaker? I'll try to explain my setup: In my office, I have my primary router/internet gateway, various computer equipment, and a sonos Play 1, all connected via ethernet. I also have an ethernet cable that runs from the office to the living room, which is on the opposite side of the house. I have several other sonos speakers around the house, connected to the other speakers using SonosNet. In the living room, I have an ethernet switch (connected to the cable from the office) that connects to several devices, including a Sonos Connect, and a second wifi router running in 5GHz-only access point mode. I was experiencing significant latency/poor connectivity on my laptop when connected to the living room access point, and I couldn't figure out why until my wife unplugged the sonos speaker in the office (thinking it wasn't important), which disabled the Sonos in the

Hi All,   I’m looking to add a turntable and CD player to my Sonos system to enable me to play some physical content that’s collecting dust.   My idea is to connect a turntable with built in pre amp direct to a Play 5/Sonos Five using the line in connection.   My question is can I connect 2 x devices (turntable & CD player) directly to the speaker via a line in ‘y’ splitter (see below)  If so would the Play 5 recognise which input was playing and switch automatically or would I need a different cable that did the switching?   Any comments/advice would be very welcome.   Cheers.    

I’m considering making the leap to ipv6.  Will my sonos products work with ipv6?  What about my older products like ZP100s and play5 (ver. 1)?  If not automatically supported, then I shall stick with ipv4 since I dont have a degree in network architecture to know how to make it work (dual-stacking, blah blah blah).  And I dont suppose Sonos shareholders are clamoring for ipv6 support. Thanks!

Hi! Is there any type of Bluetooth product out there that could somehow tap into the Sonos Connect (that I’m using for my turntable) and stream music to my Bluetooth headphones? Some days the family just isn’t into Dad blasting his tunes, if you can believe that. Thanks!

I have a PS4, and a projector that does not have optical audio nor ARC output. I would like to connect my PS4 to my Beam via optical audio. When I do this, the Sonos app does not recognize any source. Is this possible? Please advise. 

I’ve just had a new Sony Bravia and I’ve finished setting it up with my Playbar and 2 x Sonos One (Gen 2). I’d spoken to a rep at the place I bought the TV from and they assured me that I could use my setup as surround sound, which I had been unable to do on my previous TV. I have the Playbar is plugged in via the Optical port and the Sonos One’s are setup in the room as the surrounds. I’ve setup all audio settings on my TV and Sky Q box to Dolby Digital but I’m still struggling to get the audio I was expecting. I read online that all TV channels don’t necessarily output DD5.1 but I’d have expected Sky Cinema and Sky Sports among other channels would output as DD5.1. I’ve cycled around some channels and check in my Sonos app and I can see the audio on my Playbar is only Stereo 2.0. The model number of my new TV is KD-49XG8396BU. I’d really appreciate some advice.

With the new Sonos Arc, did Sonos missed an opportunity in not supplying an HDMI out?    I am setting up a projector and will use a Sonos Arc, but there will be no way for me to use Dolby Atmos. The source I will be using is a Apple TV 4K and a Sky Q 2. Both support 4K and Dolby Atmos. The normal setup would be to connect both sources into a TV and then connect the HDMI eArc from the TV to the new Sonos Arc. But since I am using a projector (same if one would use and older TV), there is no HDMI with the Arc output on the projector.    Many new sounds bars mitigate this issue by having a hdmi out on them. So you would plug your Apple TV or Sky Q direct to the Sonos Arc and then from the Sonos Arc to the projector.    I understand that only enables you to connect one source at the time, but one could use a HDMI switch before the Sonos Arc to achieve this. For example the Philips Hue HDMI sync box could be great.    But it looks like there is a miss opportunity here. I cannot see any HDMI

I’m an IT engineer and have an enterprise class wireless network in my home.  I have 3 Meraki access points all broadcasting the same SSID with 2.4 and 5Ghz enabled.  Each access point is on a separate channel following WiFi best practice of 1, 6 and 11.  I would prefer to run Sonos in wireless mode but that doesn’t work, I get all kinds of sporadic behavior.  So I have been forced to run in SonosNet mode and using channel 11 for SonosNet.  Which still of course conflicts with my AP on channel 11 but at least it is the farthest away from any Sonos speaker.  Has anyone successfully got Sonos working on a Meraki wireless setup with 3 or more AP’s?

UPDATE: I have just realized there is an “advanced setup” section of the forums. But I don’t know how to move my existing question. If a moderator can move it, please do!   I’ve had a Sonos system for a while (all Play3s)  always with one wired to my home network. Times have changed, my home network has grown more complex and now I’m in the situation where I have several APs all using the same SSID but on different channels. This is a common practice to increase coverage, but the end result is on 2.4Ghz, the APs are already broadcasting on either 1,6, or 11. Letting Sonos use SonosNet, just ends up causing interference both to my wifi network and to Sonos. I use my wifi network for a lot more things, so I’m not very tolerant of interference from Sonos here. I’m comfortable with the reliability of the wifi network, so I decided to try moving Sonos to my wifi network. A few things surprised me, so I thought I would ask here: I’ve got at least one spot it would be easy to use a wired con

Bonjour   Depuis que mon routeur wifi a été changé, mes appareils Sonos (j’en ai 11) ne peuvent plus être configuré.    Pour contourner le problème, j’ai dû brancher une enceinte sur un fil Ethernet   Je n’ai pas la possibilité de saisir le mot de passe du wifi   L’application Sonos Controller me dit: Mot de passe erroné  Que faire ?

hi all, i have a mix of wired and wireless units around the house inside and out. The colours on the matrix change often with sometimes red showing but the system works without dropouts.  As you can see on the screenshot there are several undefined devices. i have several root bridges, not all devices have the noise floor info and OFDM info also. I have my managed switch with STP on, but this setting makes no difference to the squares showing that the STP is forwarding, this is the same state with the STP turned on or off on my switch. I've also made sure all devices have their IP listed in the DHCP table of my router so they get the same IP every time. looking for some help thank you  

Hi all, I have a very nice 5.1 full sonos SetUp; 4x Sonos OneSL + PlayBar + Sub Listening to TV is great with the central sound coming from the PlayBar under the TV Experience with Music is not good because we can not TurnOff the PlayBar without having off also the Surround….. How can I set-up my installation to listen music only with the OneSL+Sub WITOUT the PlayBar ?( way too much presence of the PlayBar) Thanks to all !!

I use my Amp to allow me to use my Monitor Audio Bronze 2 Stereo speakers. I have now ordered a Sub which I want to use with this set up but have a concern. Will it integrate and perform the way it should? ie. will the Sub take the bass sounds 'away' from the MABs, deliver enhanced bass and allow them to deliver 'better' mids and highs?

Hi My PC has two active studio monitors connected via an audio interface. Is is possible to add these speakers to my current Sonos system if I purchase an Sonos Connect of some sort? If I can, will the Connect need to be a Connect:Amp or would an Gen 2 Sonos Connect (without amp) work ok? I’m also reading about a 70 ms delay with the Connect. Would this mean that my monitors would be out of sync with the rest of my system if I’m streaming e.g. Spotify, or from my line in turntable through the house? Thank you for any help.

I’m trying to figure out what the best setup would be to do a 5.1 setup with in-ceiling speakers only? The house I’m working on is pre-wired with 3 front speakers and 2 rear speakers, all in-ceiling. They want to utilize these all since they “paid for it” instead of simply going with a Playbar/Beam w/ rear surrounds.  What’s the best way to make this work?

I’m working with 8 Sonos Connect devices, plugged into a managed switch. The Sonos devices are daisy-chained in a pair of four. Meaning they’re only 2 total network cables connecting to the switch. I quickly learned about the issues w/ STP/Broadcast storms after having plugged more than 1 of these devices into the network. I was able to find a helpful document on configuring STP on the Dell switch to accommodate this. Even so, I ended up plugging in a small, unmanaged switch solely for these two Sonos connections, and a downlink connection from the unmanaged switch to the Dell PowerConnect. This seems to have alleviated the issue with STP. Here are some questions I’d love answered, if some of you can spread the knowledge. What is the exact, technical reason plugging two Sonos connects into a managed switch leads to a broadcast/STP issue? Aside from the solution, I’d like to have an understanding of what internally is going on.   I added the unmanaged switch to remove the issue. Would y

I am building a multiroom set up through our house using 3 Sonos AMPs and existing wired passive ceiling speakers and bookshelf speakers. Using the Sonos Amp for what it was intended to be used for is working very well. However, We also host live music gigs at home and it would be great to be able to connect our analogue wireless microphone system into the line-in on the Sonos AMP, to then amplify the sound out to our wired ceiling speakers. No streaming required.   I tried this last week and the latency made it unusable for live music, even with uncompressed line-in on the Sonos AMP.   I understand from other threads and the help pages that this is because the AMP uses buffering to help with reliable streaming to wireless speakers and causes a delay of around 75ms.   Last week I hooked up the wireless microphone system to the line-in on an old school HiFi A/V receiver / amplifier, connected to the same ceiling speakers and achieved undetectable latency. However as we are moving to a S

Hi all   My older Sonos system worked fine. Playbar, 2 play 5 gen 1 and a zp80. I have virgin media and used an ASUS RT60 as a repeater as the house is big enough to need help with a stronger WiFi signal.    I decided to upgrade, using the original upgrade program, to two play 5 gen 2, a Port and a Move. (I will pass over the annoyances in Sonos changing the policy to allow older devices to be kept/used).    At the same time I also bought a Tenda MW6 mesh system for my house, with 3 units. They are in bridge mode and I was using the virgin modem router alone as a router (not the ASUS).    I engaged with Sonos support as when I connected two devices with cables, my network went down. Turns out the virgin modem is poor so I connected the ASUS again and ran the virgin unit in modem mode. No more crashing, all good.    However, I’m finding that the Move - which has to connect to the WiFi rather than SonosNet - is causing issues. Issues listed below:   I’ve had devices disappear momentarily

Have my Sonos network on Unifi US-24-250 Switch - 4 wired (wifi off on 2) & 6 wireless Network gear is ER-X → US-24-250 off that is 2 x UAP-Pro and US-8 in the shop. Experiencing dropouts when using RTSP across switch and then enabling STP on Sonos wired ports. When entire switch is using STP, there are a variety of issues with non-Sonos wired devices like slow connect-to-LAN times. I’ve read a number of threads from different time frames and wanted clarification on current best practice settings for Unifi switches? I’m currently running STP (4096) on US-24 and STP (8192) and having dropouts? This was the settings before playing around with RTSP config mentioned above so I’m at a loss. Can submit diagnostics or anything else if requested. Would just like to make this work on all fronts.   Sonos Support InfoUS-24-250 Config 

Dear friends! I am working on new Multiroom Audio Project. We have a 4 floor house. Total number of Sonos devices have to be 50+. I know that maximum number of Sonos devices in one system is 32 units. What is a best way to divide system? Do somebody did same systems? Need advice from practice. =)  

Hello I just purchased a Sonos Port in order to connect my Beosound 3200. I ordered this cable and connected to the AUX in my B&O system, and to the “out” on my Sonos Port. Nothing is happening, no sound no music. Tried both Sonos App and AirPlay. i tried on another system I have (a Yamaha soundbar) amd works perfectly.    attached is the cable I have. It is a 7DIN, now waiting to receive a 5DIN hoping it would work.    do you know why Sonos port is not working? 

I have 30 Sonos components hooked up in this house. Two Playbars, Five Subs, One new Amp, Two Play 3, the rest mainly Sono Ones G1 with one Sono One G2, and a handful of Play 1s. Two boosts.   Main problem is when I switch from Pandora to Apple Music. The devices cut in and out for one to two minutes. Also I’ve noticed that on my downstairs Playbar surround sound when playing music it gets a half second lag after a few songs. This is the only room that has ever played out of sync. Only way to correct is by powering off the room and then bringing it back into the fold.   I looked at my Sonos Matrix and so much of it is RED RED RED.

I am trying to find the best way to integrate Sonos with my already pre-wired family room sound system.What I have:   Living Room 4 rear speakers (pre-wired in the ceiling) Front LR speakers (pre wired in the wall) Front Center speaker (pre wired in the wall below the TV) TV above the fireplace Currently using a Receiver in the basemen Rest of House 12 other zones in the house with a 12 zone amp in basement.  I plan on using Connects or Ports for all of those (NOTE: all zone speakers in the ceiling wired to the basement). What I want: The ability to play music via Sonos to all 7 in-wall speakers in family room. The ability to hear my TV sound coming out of all 7 in wall speakers The ability to also play the TV sound in any other room (I can live without this) Use my existing speakers instead of putting an ugly soundbar in front of my inwall speakers (seems tacky) I NEED a great quality center channel… I can't hear dialog very well with current set up. My Challenge: My TV is in the livi

Has anyone had any success in setting up a wifi only environment with the ORBI WIFI 6 router and mesh system    I am trying to set up the MOVE and I can’t get it    Is there some workaround to the 5ghz issues as I believe the Orbi only broadcasts in that space   Thank you   Peter