Components and Architectural

Hello,I am wanting to add two speakers outside my house. My current setup is one sonos amp that is hardwired to 4 (non sonos brand) in ceiling speakers. The amp is also connected to my TV and soundbar via an hdmi line and via an optical line. My bass is connected into the amp as well.I am just wondering if there is a way to add 2 more wireless or wired speakers to the system in this currently set up.  Thank you in advance.

Hi Community!I currently have an integrated amp with multiple inputs (turntable, CD player, AM/FM tuner) and multiple passive speaker outputs grouped by room (kitchen, patio, living room, etc.) The speakers are connected to a switcher for each set (room) and connected to the integrated amp via two L/R speaker connections.I am wondering if the switcher could connect to Amp via the two L/R speaker connections (thinking yes). However, I do not know how to solve the component input question. Would I need a preamp?The goal is to take my existing analog/passive system, integrate it with SONOS speakers, and control everything through the SONOS app. However, the speaker switcher would probably be recognized as one channel, right? Would I need an app for each room, then? Thank you!

I have a Nuvo based system that has 8 separate zones and 12 pairs of wired speakers, each pair driven by an Elan amplifier (12 amplifiers total).  The Nuvo Music Port has gone bad, and I’m thinking of switching to Sonos.  Since I already have an amplifier for each speaker pair, I’d like to use the Sonos Port as the source as opposed to the Sonos Amp.  I’m thinking of combining a few zones so I could cover the entire area with 4 or 5 Ports.  While this will reduce the independent zones to 4 or 5, I won’t have to buy 8 Ports (or even 12 if I wanted one for each amplifier).  My question is whether the Port’s output can be split 2 or even 4 ways to feed the amplifiers without having a problem with signal attenuation.  Comments from anyone who has experience with this would be much appreciated.

Hi, I would like to get Sonos system (I don’t have any yet). For the living room:I’d like to keep my KEL LS50 W1 and my subB&W DB4S.I’ll use this system for music listing and watching TV.I understand so far:Sonos amp: Ok for the sub but I need passive speakerSonos Port: Ok for the speaker, not the Amp, not the TV (lag)I’d like to Add 2 Era 300 has a rear speaker.Not a big fan of esthetic of a bar in this room (arc)  For the dinning roomI’d like to connect a beam gen 2 to the second TVIs gen 2 a big difference w Gen 1?Add 1 or 2 speaker in the open kitchen (Witch one?) If the community can help me specially for the living room !  

Hello everyone, I want to install a  Sonos system at home, my idea is to install 3 sonos amp, i Will conect them wired to a not gestionable swicht next to my router.My doubt is related With  the WiFi conexión, i have at home 3 diferent acces points around home same Id and password also in range in the main network, Will the App work, do i have to make am especific configuración of my network.

I moved to a new house with an existing Sonos soundbar and an Sub Woofer that was connected to a smart home system (i could not set up Sonos System by myself yet) the house has built in speakers with an 5 different zones (10 cables). Is there a Sonos Amp I can get to connect these cables and the existing speakers to be controlled by the Sonos App? it seems all the amps only connect one physical output.

Not counting the S1 vs S2 benefit, is the new equipment better from the perspective of musical qualities?My main problem is that I use a single ZP100 as both an amp to drive a set of speakers in one room, and effectively as a ZonoPlayer by using the Audio Out connected as a source for my HiFi (turn off Hi-fi if not needed in that room or turn down Sonos Zone if not needed in the other). This does not seem possible with the new Amp (no audio output). So that aspect will need to be reconfigured.It is the improvements in sound quality that currently interest me. As always thanks in advance for any insightsEnEm 

HiYesterday, I installed my Port and it worked largely as advertised. My system has a turntable, vacuum tube preamp and vacuum tube power amp. The port’s RCA inputs are connected to the preamp’s output, and the port’s RCA outputs are connected to the power amp’s Line in. I can play the turntable through the Sonos speakers, which is why I bought the Port, but I can no longer play the turntable just (not through the Sonos speaker) through the hifi speakers without first removing the Port. Is there an app setting I’m missing, or does the Port not just pass through audio signals if the app is not in use?

I have a Sonos 1 system with several speakers that are only able play at Sonos 1 level.I inherited some classic vinal and want to play over my existing level 1 speakers.I purchased a Connect and have the line out from the turntable going into line in on the Connect.The connect is connected to my Sonos 1 system and I can see it in the Sonos app.I cannot get any music to play through my speakers, have I purchased the wrong “Connect” to play my albums on my Sonos 1 system.Thanks in advance.

I have a large outdoor installation of speakers connected to Sonos Ports. I wanted to create a schedule to disable/mute the speakers from 10PM to 10AM to prevent family members or guests from accidentally playing music outside and annoying my neighbors. It’s happened several times as they don’t always pay attention and there are so many ways to select the outdoor speakers (spotify, airplay, etc). Having the ability to have restricted or blackout times would be very helpful. 

General question: does boost help with connectivity issues when NOT using the Sonos mobile app?  I get drastically different results when streaming music through Sonos app and Apple Music. When stream from apps other than Sonos, performance is spotty and spottiness increases when streaming to higher number of speakers. 

Have 6 Sonos in ceiling speakers with Sonos amp. Bringing amp down so it doesn’t cook in my attic, using wall plate to connect. Wiring in parallel per Sonos guide, can I just use a 4 binding post (2 pair) wall plate and consolidate in the attic combining 3 speakers per banana clip? Or is it better to have a 12 binding post (6 pair) wall plate and then consolidate LR ± in the Sonos amp. Would prefer to do the first as the mess will be on the other side of the wall vs in my cabinet and visible. TIA

Can the Port driving a slave amp be configured to work with an ARC to drive rear speakers in surround? Dan

I am planning to add a phono to my sound system setup. I currently have a port connected (Digital Out) to an external Analog-to-Digital Converter which then runs to my stereo preamp, then amplifiers, then speakers (of course). In this way, I am avoiding the Port A-to-D, and using my supposedly better fidelity off-board converter. If I were to connect a phono to the port, I assume I would connect to the line in. I have a few questions: I assume the RCAs labeled “Out” on the port are analog outputs? Do I connect the phono pre-amp before the “In” RCAs, or after the “Out” RCAs? I read before the “In” is correct, but does it matter? Would the phono signal be available at the output RCAs, as well as the digital out?  Would the output RCAs have been digitized/un-digitized, or would it just be pass-through? In other words, would the line-in source be passed to the “Out” RCAs without going through a A-to-D and then an D-to-A?Obviously, I could just route phono to phono pre-amp, then to stereo p

I’m considering getting a half decent CD player - perhaps a Marantz CD6007.  Highly rated, decent DAC, looks good - what’s not to like.  My only speakers are my Sonos - Five / Play:5 in a fairly inaccessible location in the kitchen, Beam 2 / Sub / 2 x Symfonysk lights as my TV surround in the living room, and 1’s dotted around the house.What’s the best way to connect the CD player?  Logically the answer is the Port, but I see people say a Five is “just as good” an option.  it’s just mines are high up and  not necessarily in the right room to listen or run a 3.5mm cable to!At some point I’d perhaps consider Era 300’s for the living room, though (and this is tragic) the fact the Symfonisk’s are decent side lights is actually one of the draws to keeping the Symfonisks, and I’d need new lights to replace them, and have to figure out how to fit both Era’s and replacement lights on to very small tables.  As I said, tragic, first world, stupid problems! 🤣   What do you think my best option i

Ever since I upgraded to the Sonos S1 iOS app a few years ago, I’ve been having connection issues. Here’s what’s happening: I have a Sonos Connect:Amp. The amp is in a basement cabinet with router and cable modem. I have 2 exterior rock speakers that are hard-wired directly into the amp. The amp is connected via Ethernet to a small hub that’s connected to the WiFi router right next to the unit. The Sonos LAN settings are configured for Ethernet (says WM:0) in About My System. I have 2 WiFi networks. Call them Primary and Secondary. The reason for the Secondary will be explained below. The Primary WiFi network is an Apple AirPort Extreme (located on 3rd floor) with AirPort Express repeaters at different spots around the home (garage, basement and pool cabana, all Ethernet wired). I have full strength no matter where I am. It’s been rock solid for years. Secondary WiFi is actually the cableco provided router with a WiFi option that I have turned on. Here’s the Sonos issue: While connecte

I have two Sonos Connect devices (in different rooms) running S1. Device A is connected by ethernet and B by wifi. RIght now, my router reserves bandwidth both for the Ethernet connection to A and for the Wifi connection to A, along with the wifi to B. (The router recognizes 3 Sonos connections.) The problem is the router partitions bit-speed, and I'm at the limit of what my ISP can do. So I want to make the A connection eithernet only, bringing down the denominator by one in the division of bandwidth. Sonos does have a setting for that, but when I disable wifi to A, mysteriously B disappears from my system. Can anyone help me fix this? 

Hi, a have a problem with my Sonos (bridge, Connect:amp, playbar and sub) I try to Connect to new system, but only bridge was able to Connect When I try with playbar it doesn’t work :( I reset a playbar and its flashing green light, Sonos s1 app finds a playbar (after that I push the buttons) but when I click configure its shows „not connected” and it says „Sonos product not found…” I also try with lan, but the same things happends Please help 

I know Sonos says they only support 6 speakers when using Architectural series speakers, however, has anyone had success with 6 8ohm speakers connected to a Sonos Amp?  If so kindly advise.  I’m looking to setup 6 outdoor rock speakers which are 8ohm and wondering if it might work.  I’m not looking to play them super loud and already limit the volume to 80% to prevent clipping on the current Connect: Amp that is powering 4 of them today.  Thanks in advance!

ScenarioSonos amp connected to router by wireRouter visible on phoneLine in is bluetooth receiver playing music from phone.Line in is set up and working  when i have internet on App i.e. playing over BTIntetnet goes bye bye (virgin are crap) . Line in drops out.Surely i dont need intetnet to do line in ?   

Hi, does anyone know if I can use the Sonos Amp Gen 1 to listed to my vinyl turntable (not sonos) to my new Sonos One speakers?Thank you

I would like to listen to TV audio through my Sonos Port and other 4 Sonos Amps.  I currently have a surround sound receiver playing TV audio and the receiver is connected to the Sonos port.  I was told by Best Buy that the only way to do this is use a sonos sound bar but that defeats the purpose of the receiver / surround sound system.  In a perfect world I would be able to watch a television channel (perhaps a football game) on Directv and hear the sound throughout all of the Sonos amps in my home.

Unique question this.I am thinking of purchasing a Spectrum Analyzer to bring some life to my home setup. I’d like to achieve the following:Connect my turntable (amp built in) to my Port, audio to be played through my various Sonos speakers Connect the output of my Port to a Spectrum Analyzer (the Spectrum Analyzer has RCA inputs) The Spectrum Analyzer to display the output signals from the turntable, and a different times the output of other Sonos audio services connected to my wider Sonos setup (i.e. Spotify)  Is this workable? Could the Port support such a thing? Basically outputting the sound from my turntable or other Sonos audio services to a Spectrum Analyzer all via the Port’s output cable?

Bonjour je remarque que l’enceinte Sonos se déconnecte souvent du routeur wifi, est ce que c’est possible d’intégré dans l’enceinte un accès point comme ça on dépend plus de la distance pour se connecté directement au système Sonos.Merci

Hi.  I recently got a Sonance 6.0 system to add to the other Sonos systems in the house.  I had no problem setting the Sonance up and it seems to be working fine on the wifi.  When I try and take the volume above about 60% it always cuts out.  Works fine up to that volume but always cuts out above that.  Any suggestions?  Thank you