Portable speakers

I have an Arc, 2x 1st gen One’s, all hardwired, plus a Move, all running 12.1 60381140. Until I setup the Move, I had never configured WiFi credentials to any of my Sonos equipment, and for some asinine reason I had to enable WiFi on a One before the setup would even acknowledge I had a Move to add. After configuration, WiFi has been disabled on all wired devices and everything has functioned as expected.I now need to change the SSID the Move connects to, and the iOS App again refuses to begin searching for WiFi until at least one of my hard wired devices has WiFi enabled. This is mostly venting of the stupid precursor steps required to get to the real problem I’m posting.I have the new SSID setup, every other device has been updated with the new credentials and is functioning as expected. The Move connects to the old SSID just fine, but searching for the new SSID using the iOS App (S2, 12.1, 6038140) fails to authenticate. I don’t even see an attempt on the AP, it’s just silently fail

Hello! I have a Sonos Move (as well as a few other products). Everything used to be set up just fine, with the Move in its own group. Recently had some issues and had to replace a lot of electrical wiring in the house and the axial cable to my modem got fried. Replaced the modem and router.Everything is set up on the new network, except the Move. I have tried rebooting the move a couple times. But still when I try to get it into setup mode, the light goes solid orange, never flashes green. Additionally, my Sonos app seems to have forgotten the Move was ever there. Is this a hardware problem?

Dear all,I have a Move and I’m unable to charge it.I used the charging base provided by move but the battery always remain at 0%I bought Move this year so I don’t think that I need to change the battery.anyone with the same issue? thanks

Move has worked fine for several months and has just stopped working altogether.  No LED lights are on.  I have tried the reboot, plugging into a regular outlet, etc.  All I’m getting is a solid red light on the lower front LED that goes out after a few seconds of sitting on the charging ring.  Move does not appear in my app.

At a rent by week cottage and attempting to setup a Move on a wi-fi, it fails to complete.  One article says the Move cannot be setup on a guest wi-fi network. How do I know if the wi-fi I'm trying to connect to is a guest one, and that's why we can't connect, or some other problem is in play?

I picked up a brand new Move. Followed the connection instructions for WiFi. It connected and it shows up in the Sonos App. Works fine when using the App. When I press the MODE button on the back to switch Bluetooth, nothing happens. It does not beep or chime. Further, I’ve tried holding it down for pairing. Nothing. No beep, chime or blue light on top.  Also, Move is supposed to be AirPlay 2 compatable, it does not show up on the list of devices. Any ideas on how to get these things working are welcome. 

Hello team, I was trying to use my SONOS Move via airplay through my Ipad and Iphone and it’s not working, it keeps saying connecting and then says connection failed. Tried to restart it, restarted my phone and ipad and it is still not working. Any ideas on how to proceed on this one? Since the Sonos App 2 doesn’t allow the option to hard reset the device I don’t know how to proceed.I am using the Apple Music app, it works on Spotify, but I don’t use that app. Please provide any help over here and I will be thankful for a lifetime :)

I moved the Sonos to a new house/wifi but am unable to connect. I have tried the app and after recognising the Sonos Move, it asks me to enter to details of the wifi to which it should be eonnected to and then after a while, it says there was an error and couldn't connect. I have tried reinstalling the app on the phone, tried the app on a different phone, tried keeping Move next to router, reset Move etc etc with no success. I have also tried installing the old Sonos S1 app and tried but without success.    Any ideas on what I could do/try?

I have had a sonos move for 2 weeks (since 04/07/2020) and until yesterday all appeared to be working fine. This morning I noticed the Move was no longer showing on my App. However, I could play music through it using Alexa. I searched on the forum and one of the suggestions was to re-set by opening off for 5 seconds then holding the connect button until I see the orange light. I have done this and the app finds the “new” product and gets to the wireless set up. I have entered the correct password but it is not able to connect to the WiFi for some reason. I then deleted my WiFi network from the App and set it up again and all my other speakers are happily connected. I reset the move again and went through the same process, ensured the password was correct and still unable to join. I am now unable to even play through Alexa. Also, The move is 2 meters away from the Router so I don’t think that should be causing the issue.   Please help!   Diagnostic: 134107060  

Hello, I have one house with WiFi and my 2 sonos one are working well, but i want to listening music near the swimming pool but my wifi dont reach that area so i connect one cable from my router (ROUTER TP-LINK TL-WR940N) to other router in the swimming pool area, the WiFi is working very well there but i cant connect my sonos move to this new WiFi. can someone help me? Best regards, João

I have been using the Sonos Move for almost a year and recently purchased the Playbar. I love both of them but they can’t seem to pair. Is this a known issue?   

I just got a Sonos 5 delivered yesterday and already have a Sonos Play 5 (2nd generation). i tried to Stereo Pair them on the Sonos app and it does not seem to work. I was really looking forward to the stereo pair and assumed they were compatible.    Can I Stereo Pair a Play 5 with a Sonos Five?   I think i already know the answer and they are considered two different products.   Thank you,   Juan  

I got my Sonos Move yesterday and intend to use it in our patio.   To my horror, it started playing and then went dead.   The WiFi signal wasn’t strong enough and the patio is maybe 5 or six steps from the router but on the other side of a sliding glass door.  I have had a Sonos One sitting on the patio but almost touching the door and it works fine.   But it is using the Sonos network, not WiFi.   If I open the door, the Move works fine but I let the air conditioning out.   I thought the Move is using 5.0 - not 2.4 (which can go through glass doors easier, I believe) but it already is using 2.4 and the title of this post is wrong.   I found an iPhone App to measure WiFi signal strength and walked around measuring with the glass door closed…..I found a “hot spot” and I believe it is because the spot also had a view of the bedroom window and was getting signal from there as well (I have a Google WiFi mesh with a node in that bedroom.  The Move works well in this hot spot but it isn’

I have a 5Ghz router which of course also can use 2.4 ghz. The sonos app can only find the 2.4ghz network, why is that? ( i use an older bridge to connect my system). if the sonos system uses 2.4 ghz network and my app device uses 5ghz i can see and control all of my speakers but not the Sonos move. That i do not understand. Someone who can explain that to me.  

I am away from home in a family house (different wifi network, geographically separated), but have bought a Sonos Move. What’s the best way to set it up? I want to be able to start using it, but then when I go home have it join the rest of my main Sonos system. Should I set up the move with a new/different Sonos account (email) at my family home, and then when I return home, should I factory reset the move and re-set it up on my home wifi + home Sonos account? Should I first set up the Move using the same Sonos account but different Sonos system (apparently one account can have multiple systems?). Then when I take the Move home, somehow have it join my home system (I hear the Move can join multiple wifi networks?) Is one better/cleaner? I don’t plan on moving back and forth between these two places, I just don’t happen to be at home when first starting to use the Move.

When trying to AirPlay from iMac 17-inch, Late 2006 running Mac OS X Lion 10.7.5 (11G63) I’m getting an error: An error occurred while connecting to the AirPlay device “Move”. An unknown error occurred (20). iTunes version 12.2.2.25At the same time, airplaying to Beam with 2 Play:1s works fine. Any ideas?Thank you.

I am trying to setup a new Sonos move, and when I get to the WiFi setup screen on my iPad and choose my WiFi network, the next screen says “Enter your network password.  We’ll set Sonos up on: <MyWiFiSSID>”… and on this screen there is no box to actually enter the WiFi network’s password.  Then when I click Continue, I get “Verify network info for <MyWiFiSSID> Please wait”…, then after about 20-30 seconds, I get the error “Password incorrect.  You need to enter the correct password to set up this speaker wirelessly.”What am I missing?  Whey doesn’t the app have a place to actually enter your WiFi network’s password?… I am stuck and cannot continue beyond that point.

I’m sure this has been asked, but I couldn’t find an answer to this. I previous was living in a place with my own internet, modem and router. I just moved and the unit I’m moving to shares internet with the unit upstairs where the WiFi router is, so now have no wired options available to me. I need to update my play de, Sonos 5 and two sonos 1’s to the new internet via WiFi. Is this possible? If so how do I do it?