Components and Architectural

Hi all,With the new firmware 13.4, I try to configure DTS with my PS4 and my sonos ARC.I have a TV Samsung with eARC, and my PS4 is connect to my TV with HMDI.on my PS4, “audio outpout setting” is on “bitstream DTS”, my TV is configure on “passthrough”, but ma Sonos app display “Dolby PCM multicanal”. So, it’s possible to have DTS with PS4 with the new firmware ?could you help me ? :)

I use S1 with a Connect on the same network where I have multiple other devices running S2. It’s always worked fine. Today the S1 app was not connecting and seemed to not even know my ID. I logged out and logged back in and then it told me to use S2. Of course the S2 does not work with the Connect so I factory reset the Connect, reinstalled the S1 app and tried to connect the Connect. No dice. Tried everything and finally had to dig it out of its location and plug it hard into the router. Got it set up but the S1 app was acting weird and would log into my account but then lose connection with the Connect. Then it would say “we found Connect” and I’d click on it but have to log into my account all over again. THEN all of my services were gone so I added them back and it said “oh we found them!” one by one. Sheesh I did all of this but it would not play. Seemed to be lost trying to find the Connect and my account. I was 90 minutes in at this point. THEN…… It told me I needed to start usi

I had my Sonos music library setup on a USB stick in my WiFi router. All has been working fine, including playing songs from that USB source and running regular updates of the music library (re-indexing). Now I'm getting this error when trying to update the music library:  Music files not available[usb location on router] is no longer available. The device where the music files are stored may not be powered on, or the path may have changed. Go to Settings > System > Music Library Setup to check the path.Even after this mesage was displayed, Sonos could play songs from the USB drive (i.e. from the existing music library) absolutely fine, so the potential issues mentioned in the message don’t apply; it was just the music library update that stopped working. To try to fix things, I deleted the music library reference from Sonos and tried to add it again. (I did this using the Sonos desktop app to navigate to the required location on the USB drive, so Sonos can definitely find and re

I am recapping my ZP90 at 12 years old. The caps mostly appear good, apart from the 1800uF on the 3.3V supply, which has a bulging top. I think its testamount to a good design that these units last this long. I leave mine switchedd on all the time, with 230V nominal mains.These are the main capacitors, all originally by Jamicon, to consider replacing. They should be replaced with parts with same or better ripple current, life hours, and similar ESR. I avoided organic polymer etc, which might seem an upgrade, but which could lead to loop instabilities. My cap choices were rather limited by stocks.400V 22uF main reservoir. 20mm long maximum. I am going to use https://hu.mouser.com/ProductDetail/Wurth-Elektronik/860241378003?qs=sGAEpiMZZMsKEdP9slC0YVUSgIC2sJFYWYuR0ZnncGk%3D22uF 35V C104 - low stocks meant I am not going to worry changing this. value for info. Its the aux supply for the switcher IC.C206 1800uF 6V3 105c Jamicon MZ 18 tall dia 10 pitch 5. I will use https://eu.mouser.com/Pro

I can manage my system with an iphone.  If I try to manage it with an ipad, either the system is not found or the Move is shown as the only device.  I have deleted & re-installed sonos app on the ipad to no effect. Any ideas?

My Connect:Amp has disappeared from my SONOS app. I also have a PLAY:1 and PLAY:3 and both show and work.All were bought new and installed when I moved to a new home 5 years ago and have worked perfectly until now.I’ve tried powering the amp off and then back on, but it just doesn’t appear. The network hasn’t changed.I’m sure to be doing something wrong, or missing a trick but would appreciate some tips please. I haven’t found anything here that has helped so far.

Hi,I manually added the radio station by pasting the following URL to the field in the Sonos app: http://web.sabc.co.za/digital/player/1.0/rsg/index.htmlAfter successfully adding the radio station I received a message that the song cannot be played because it is not encoded correctly.Can someone please get me the streaming url for the above. Not sure how to get it in Safari on a Mac.  The previous one I got from the forum does not want to work anymore.  Seems like SABS keeps on changing the streaming URL.Thanks

I have a Beam and a one that are 2 years old not working well with Sonos app.  Should I be using S1 or S2 app? Should I have the original Sonos app & S2 loaded or just S2? My problem is the sound fades in and out and Alexa drops off. I use it with a Sony android smart TV. 

Within the last couple of months, Sonos will randomly say “Something went wrong, please try again later” at max volume and always very early in the morning, usually between 4-7am. We don’t use any voice assistance on Sonos, and we never play anything at max volume, so the fact it plays the warning that loud is strange. Anyone have any ideas how to fix this?

After 3 years, here I am once again with no Sub. Tryin’ to upgrde to S2 controller, I added my devices Playbar and Sub (new way to do it, not so intuitive, but that’s it). After that I connected the sub, it took about 10/15 minutes. Palybar+Sub are in the same room but, once again, Sub doesn’t work (no sound) neither in WiFi nor in Eth. No Boost at the time (do I really need one, with S1 all was perfect).1 hour to make work everything, but...no way to do it. For about 10/15 seconds Sub has started, but in the App I saw the “?”. When in the App I finally saw the Sub...no sound from it. Modem AVM 7590 and repeater 1750, will try again and, eventually I must use the Boost.

Hi alli know there are a number of queries on Connect dropping off a network and I have read the majority. Following advice I bought a Boost, set it up, I see all my speakers and the Connect have WM:0 against them….Connect still dropping off after a minute or 2. I have tried all 3 channels, 1 is the worst, 6 & 11 about the sameAm I looking at a faulty Connect?  

Hi all! This is a brief follow up to the above previous thread I started. The previous thread was marked as 'answered' and closed for further comment which is strange as it certainly wasn't answered! But good news, after 10 months of tantrums and frustration I finally cracked it! I wanted to post how I did because I'd say 95% of what fixed it was from other people's comments and help on the last thread. SO THANK ALL OF YOU SO MUCH! So my problem was an old house, giant thick walls, and my 11 or so speakers constantly cutting out and freezing. I had a netgear orbi mesh system. Now this mesh system was fantastic, but I couldn't get it to play ball with the speakers and the switch between them. Eventually I gave up on the orbi, and bought an Asus router that just manages to reach all the corners of my house. This helped a lot! But didn't fix it Someone recommended I got MANAGED switch, but this was actually making it worse (see below..) although the system wouldn't be much better with a d

Short Version:I have a great room with cathedral ceilings and a TV mounted above the fireplace. I’m planning to use the Sanus TV mount to put the Arc either above or below the TV. I’m worried below may be too warm with the fireplace on. Above may ruin the sound (which may be ruined by cathedral ceilings anyway). Thoughts? Long Version: Here is a pic of the room. The seemingly important measurements are:46” - Floor to Bottom of TV78” - Floor to Top of TV16” - Between Bottom of TV and Fireplace43” - Floor to Eye/Ear Height When Seated12’ - Seating Distance9’ - Floor to Bottom of Cathedral Ceilings14’ 6” - Floor to Top of Cathedral CeilingsFrom everything I’ve read, the cathedral ceilings will ruin the “bouncing” effect of the up-firing speakers. Given that, would mounting above the TV really be a bad idea? Also, there is still plenty of height from above the TV to the ceiling, in case the ceilings don’t ruin it.  Finally, the TV is currently tilted down about 10 degrees. So the Arc will

Hi all,apologies in advance for the length of the post, just want to cover all I can to save on questions.I have looked over the forums and troubleshooting but can find a solution other than the usual “blame the users network” as the cause of the issue I will try and describe below. I am biased as I am a networker by trade but the answer of network fault makes no sense and I hope to explain why.Only in the last month or so when I add a song to a queue, that is already running, it misses any addition and continues on to the next song. If it was a network / connectivity issue it would do this to most if not all songs not just the ones I add to the list, the songs in the original queue don’t ever skip or fail to be played. This happens with different playlist queues and created for you playlists from Spotify, so random songs and queues from day to day but issue is consistent. In addition there are no error messages displayed, simply song added to queue shows when the song is dropped into

My Play:1 system is no longer able to be used because when I open the Sonos App it crashes every time. Any tips on what to do when the app crashes? Also, it works perfectly on my husband’s phone which is the same model iPhone as what I have, but the Sonos App crashes a few moments after trying to open each time for me. Any tips would be appreciated!Thanks!

My sonos playbase stopped connecting via airplay. I tried resetting and setup fails at the step where the Playbase is added to a room, when setting up over wifi. On ethernet it sets up properly. Now it only works on ethernet and not wifi.

I have 2 Sonos 1 speakers, one upstairs and one downstairs - had about a month or so. I’ve been playing music using Airplay on both speakers, when suddenly music cuts out and then random music starts playing. It appears to be from a Pandora account, but no songs or stations that seem to be on my account. Nobody in the house has told Alexa to play anything- it just happens automatically. It keeps happening now over and over after a few songs play. I re-authorized my Pandora account, but it happened again. I don’t understand how the speakers can just start playing something else without my interaction - even if it were my Pandora music. There’s been no internet service disruption today, although there was a couple days ago. But nothing happened on that day. 

Hi, I have 3 Android devices with Sonos S2 app.One is showing All speakersThe 2 others only showing half og the speakers.All Android devices is in the same WiFi as the sppekers.Have truede find lost speekers from the app.Pless help...     

Hello.  Previously had been in touch because I have large .wav collection of my recorded LP collection that I couldn’t access.  I learned bit speed had to be 16 or less; tested a conversion that worked and thought I was done.  But continued having ‘no show’ files in app, or otherwise having files not playable in a few cases.    My track filenames can be long, including composer, name of piece, movement, key, opus #, etc, and folder structure can be several layers deep.   I just today discovered that if I moved a file one layer higher in folder structure A100 would see it.   Is there a ‘total file length’ recognition limitation? Thanksmadsinger

I have bought a Sonos Amp and a Port to augment my system of 2 Sonos 5s, a Playbar and several Ones and Ikea speakers. I'm on Sonos net and have historically always suffered from interference. It's a big help being able to use the Support info to check signal strength etcHowever the Amp and the Port are showing no info or colours etc on the report. I understand this may be a change in policy from Sonos - is that the case?And if so……. why do it?

I have my Gaming PC plugged in to my TV using a AudioQuest Pearl 48 HDMI, which my Sonos Beam 2 is plugged in to via eARC HDMI port. I can play games with the sound coming through my Beam 2 for about an hour then the audio quality starts to drop in quality and distort like it’s playing through a cheap toy speaker, before dropping completely and being reduced to bassy crackles.When pausing my game the audio comes back for a period of time, although still not great before having the same issue. Quickest fix is turning my Beam 2 off and on again at the plug, but this doesn’t seem great fix to me.All devices are wired in to my network and not using Wifi. I haven’t had this problem watching content on my tv… yet. So guessing it is something to do with my PC?

Help! My Android Sonos app suddenly stopped connecting to my three Sonos products yesterday, without me having made any changes. It just suddenly says "Unable to connect to Sonos", and when I follow the instructions to try to fix it, none of it works. Essentially my phone tries to bring the products into the wifi, even though they are already in the same network.The Sonos apps on my two laptops as well as another family member's Android phone still work, and the Sonos products are happily connected both within the wifi and into the internet. I’m currently listening to music with the speakers! It's just my phone that claims Sonos is not visible in the same network.I use a wifi booster, and we also have both 5GHz and 2.4GHz networks. I have played with different permutations, but even when I unplug the booster and disable the 5Ghz and am left with only one unique 2.4GHz source for the wifi, my phone still claims the currently-happily-playing speakers are not in the network where they in

For a while now it seems my Playbar is processing remote control commands twice.Whenever I try and control the volume through one of my remotes (TV. FreeSat, FireTV) the command is actioned but the white light on the Playbar flashes twice. For volume up/down it means the changes are twice what they should be, but it also means I cannot mute the Playbar.  Pressing the mute button it mutes and then immediately un-mutes!The same happens no matter which remote I use.  I have tried the ‘Remote Control Setup’ within the app but it makes no difference.Any ideas anyone?

I am hoping some other people have experienced this issue.  Typically it happens on my iPad (pro, air and mini). If I am watching an app like AT&T TV or Direct TV stream on either device and try to play the sound through any of my sonos speakers the screen will grey out and display “Airplay”. I can hear the sound through my speakers however the video is not displayed on my device. If I switch my “move” or “roam” to bluetooth it will work normal.It doesn't happen on Netflix or Hulu. But it will happen on HBO Max, Direct TV Stream, Starz, and a few others. Has anyone had this problem and found a fix??  

Hi there, is it a known problem with the iTunes, that you can't add a service currently? I have deleted and reinstalled a few times, but it gets so far then just stops. Worked perfectly previously. Cheers