Troubleshoot, tune and get the most out of your system
Recently active
Hey everyone,after the (terrible) Sonos system update, the (e)ARC connection between my TV and my Sonos Amp stopped working. No sound is played at all and the TV setup in the Sonos app just states, that no (e)ARC connection is possible. As it worked before the update, of course the TV is set to output the sound to the (e)ARC-HDMI-port. Tried turning it off and on again, reconnected the HDMI-cable a couple of times, rebooted the TV and the Amp and even set the TV to factory settings and reanabling (e)ARC-output. No dice.Does anyone has a solution to this? Or do I just have to wait until Sonos fixes this problem? It’s so frustrating...
Why remote went work on been further than 3feet!
We’ve moved house and got all products up except Sonos 5. I got this on via Ethernet to the router but as soon as I move it off Ethernet is says no connection
Hi all, brand new convert to Sonos speakers and very very happy with the sound and build quality of them. Couple of issues though, one being the Alexa volume, which i ended up disabling and sticking to our old echo dot. Second was the incredible faff getting themset up as a pair ! After much googling i discovered that my BT hub was the problem? And switching off 5ghz solved it and they are now happily paired. Question is can i switch 5ghz back in without causing issues? mark.
how to delete failed arc ultra setup attempt from app?
I recently upgraded my home theater area (24'x15') with Mohawk laminate flooring and bought the "Ultimate Immersive Set with Arc Ultra" for the sound system. I haven’t bought furniture or a rug yet, but I’m concerned about how to power the surround speakers. There are no power outlets in the floor or the nearby side walls where the speakers need to go.The quickest solution might be to run an extension cord from the front of the room and hide it under a rug. However, this would require a rug that covers the space from the furniture to the TV.Another option is to get a 250Wh battery pack, which should power the speakers for about four hours at full capacity. But this would cost more, and I’d also need to figure out where to hide the battery.Any suggestions? I will hate to return my Era’s as the setup is not passing wife’s inspection :(
Hi, I currently have an arc, sub gen 3 and two era 300s. Is there a benefit to connecting the ARC through Ethernet? Does it still create sonosnet and if so do the eras still work?if the ARC is replaced with an ultra does this have do the same?I am a little unclear on this as some info suggests sonosnet does not work with newer models, but if this is true why would you connect the ARC ultra by Ethernet if it does not help with Ethernet sub and surround connection etc?I also have some ones in other rooms, how would the benefit, if at all?Just doing some research before I make any changes 😊
My Sonos Beam Gen2 volume operates perfectly from the app, but when I try to use my TV remote I get an echo.I've gone to the audio settings on the TV and attempted to switch from TV speakers to audio system, but it instantly switches itself back, displaying a message that says: “Audio system is unavailable. Switching audio to TV speakers.”Am I overlooking another kind of setting?
Hello. I just set up my new Sub Mini, paired with 2 older Play 1s I have had for years, and I must say I am not at all impressed. I can tell NO difference whatsoever with the Sub Mini set at the neutral equalizer setting, and only know it works when I change that setting upwards of +8 or more.Any thoughts? I’m really disappointed, as I was excited to add a sub woofer to my music system. (I use my Sonos system for music only, not as TV surround sound.) Maybe the Sub Mini needs better speakers than the Play 1s to notice the effect?I’m on the verge of returning the Sub Mini, so any thoughts would be appreciated before I do so.Thanks,
Situated in my entertainment room for music only, I have 3x Era 300s. The room has tall glass sliding doors with no glass tint to minimize the afternoon sunlight. Because of this, I move all units out of the sun. This is an annoying exercise, because after every use, I do this.will Era 300s get damaged in some way due to the direct sunlight (which is probably about 30min exposure before the sun goes down)? If they can be damaged due to the above, will that affect the sound output? are Era 300s robust enough to withstand about 30min of sunlight? should I continue with this after use removal to avoid next day potential sun damage?I also have a sub gen 3 in the above setup with no sun exposure
Pair of symphonik, worked fine. One speaker power got unplugged for a week or so, plugged it back in, now only left speaker works. Diagnostics show the pair is active and both speakers are connected with strong signal. Tried to unpair, but the android app would not let me. Figured I would try the windows app. Windows app required an upgrade. Meanwhile Sonos radio is streaming out of the left speaker only during all of this. Windows app starts upgrading and lo and behold both speakers are working in proper stereo! Upgrade taking a couple of minutes and finally says COMPLETE….at which time, the right speaker dropped out again and I am back to where I started. What is going on here and how do I fix it?
So I have the following speakers and am trying how to best configure what I have to get the most out of the system:(1) Beam Playbar (3) Sonos One SL Speakers (1) Sonos Play:1 SpeakerI Currently have two of the One SL speakers in the back of the room facing the TV in an elevated position and they are set up as surround system (Left and Right) with the beam playbar (Rear Surrounds). I would like to set the other two speakers up in the corners adjacent to the TV and facing the listener. The TV is mounted on the wall in center of the room. I am not sure I can pair the One SL and Play:1 speaker so currently they are just additional speakers that I have to manually control the volume in the app which is annoying. If I need to discard the play:1 speaker should I purchase a refurbished or used One SL speaker to get the configuration I am looking for or go another route? Really tired of having to maually adjust volumes for each speaker and would much rather control everything with one volume ad
Does anyone ACTUALLY know this?From looking at the exploded diagrams of both noting the Ultra’s driver shapes, especially being that its chassis is slimmer, I asked and thus got ChatGPT’s partial answer:“The mid woofers on the Sonos Arc Ultra are traditionally shaped, following a circular cone design. This design aids in producing accurate midrange frequencies for crystal-clear dialogue and balanced audio output.”And we already know there are only 6 of them on the Arc Ultra (which will arrive here either tomorrow or on Wednesday the 4th). So if they are circular, what are their diameters? (And of course the size of their magnets and voice coils make an important difference, too. But I doubt even Sonos knows what the “magnetic flux” is, which is measured in “Tesla”s.)The Arc, as we’ve known for years has 8 elliptical midwoofers, so what are their measurements (height and width)? And I’d like to know the size of the voice coils and magnets here, too.I think these diagrams will give ev
When I use Add to End of Queue to load a user created playlist I still get the error shown in the first screenshot. In spite of the error the playlist loads. Why does this still occur? Thought this was fixed.
Am unable to link my Sonos One SL to the new app. Tried everything: switch off, reset, any kind of search, using the older app Sonos 1.What should I do?In other way, would like to upgrade my only speaker to a hi-fi set. Thinking of purchasing another speaker compatible with Sonos One SL and… what? a subwoofer, a mini, a bar? Would be grateful about any advise
So, I have been trying to connect my music library located on my PC to the (newer) Android App. I can make it work from PC to PC, but many hours spend looking on the net for a solution didn’t give results.Systems: Windows 11/Android Version 15SMB1/SMB2 configuration: Music file network configuration:My Sonos App that doesn’t even validate library entry (button stays disabled): What Am I doing wrong? Thanks!
The Arc Ultra is a tremendous performer vs the Arc. Although the Arc was no slough. Everything is much more expanded especially for Dolby Atmos movies and music (both stereo and Dolby Atmos.) Dialogue is greatly improved. My media room dimensions are 14 feet wide, 20 feet length with 8 foot ceiling. It consists of the Arc Ultra with dual Sub 4’s (both off center) one front on a parallel plane as the Arc Ultra ; which is 39 inches above floor and 26 inches from front wall. The other Sub 4 is 19 feet to the rear off center. Both subs are 5 inches from the wall (not in a corner).Surrounds are Era 300’s 10 feet from the Arc Ultra and 56 inches apart on Sonos stands. They are 6 inches to rear of seating area on left and right. Yeah, they are somewhat close to seating area, but TruePlay adjusts for an immersive experience.IMO a good movie that has plenty of different sound effects good low-end, dialogue and music to really push the Arc Ultra is Twisters on 4K UltraHD Disc (released July, 2
I have a Move speaker in my multi-room system but the audio keeps dropping out constantly. Few milliseconds dropouts every 15-20s. I have tried switching the channel but it doesn’t fix the issue. WiFi is strong in every room but Move keeps acting up. I use turntable as source hooked to Amp and all other speakers (Arc, Playbar, Play:1 x2, One x4, Sub x2) work flawlessly.
After dozens of annoying trial and error sessions (with mostly errors :) I want to briefly share what finally worked.Long ago the issues arose when installing my new ZenWiFi AX XT8 mesh system, when the Sonos system wouldn’t connect at all to the system. By trouble shooting turning things like the QoS off etc, I got it to work fairly stable. Until a recent FW update (3.0.0.4.388_24688) when the issue began with intermittent audio dropouts from my two Play:3 speakers, which are used as surround sound speakers in my Sonos system alongside the Sonos Arc (connected by network cable) and Sonos Sub (Gen 3). Both Play:3 speakers would simultaneously cut out for one or two seconds before resuming playback, and this happened ever 5-10 seconds. Needless to say, VERY annoying. Despite having the Arc connected via LAN cable, the Play:3 speakers continued to experience dropouts, which disrupted my overall audio experience.Steps That Didn’t Resolve the Problem: Disabling Airtime Fairness and QoS: Do
Will the music library I created by uploading CDs for the S1 system work in the S2 system? Will the Sonos Playlists still work?
Why does the queue not follow the progress of the music? When I’m playing track 137 that’s where I should be when I open the queue. Instead I’m on page one. When will this be fixed?
I recently bought 2 Sonos Era 100 speakers. I just now got voice control going so I have the latest updates. I am having the following issues:1. Sonos does not get homophonic words right, even after many repeats. E.g. I say "Play the band Forus" and it plays something by the band "For Us" after repeating Forus, it plays "Russ", etc.2. Sonos does not seem to recognize long names. I say Hey Sonos, play "I only go to school for the handrails" and then it acts like it didn't hear me and goes back to playing what it was playing when I made the voice request. It does, however, recognize "Sunday Bombs" and plays the correct song. It seems like there is no mechanism where I can correct these errors in recognition so that it learns over time based on the music I actually listen to (e.g. tell it that Forus means Forus). Is this correct?
I have een old tv without bluetooth is it possible to buy some kind of device . So i can use my sonos ace wireless . I have a cheap bluetooth transmitter but won't work. So if it is possible i don't want to spend a lot of money.
As I see multiple people in the community having issues with Google Home and GA connectivity, please Sonos get your stuff fixed. The status page states that the google services are up and running but they are not.I have rebooted every device, router, phone, made sure that every piece of software is up to date and I still can not connect to GA or Google home.System diagnostics code *******. This really makes me wonder combined with the app issues over the last year if Sonos is still worth buying as the usability of the platform has been going downhill. Moderator edit: Diagnostic number recorded and removed
Regarding compilation CD’s they look like individual CD’s for each track in the app. they used to look ok before, is the s release issue??Best regards
Already have an account? Login
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.