Troubleshoot, tune and get the most out of your system
Recently active
Hi,Running dual subs (one Gen 3 and one Gen 4), and noticed in the app it gives me only one control for both subs. Meaning…..the crossover setting is there only once, and the phase setting is there only once. So...why wouldnt I be given the ability to set crossovers differently? and are both subs phased the same? wouldnt you want to have the phased opposite for best impact? I am no expert, and am open to all feedback. Thinking I might add a second AMP so I can control my second sub the way I want. Does that make sense? TIA Moderator edit: Changed “One Gen 3 and one Sub 4” to “one Gen 3 and one Gen 4” for clarity.
I am building a new house. There is currently no drywall so i am able to audio everywhere. My plan is to do 8 speakers in the living room, 2 in the master bedroom, few in the patio etc. My question is, how do i wire 4 speakers to 2 channels from the amp? Do I just go + to + on 1 architectural in-ceiling speaker and follow that to the + on the second speaker? Same for -? Thank you!
Hi All,This is a security question for the security concsous amongst us. I realise i sound like a paraniod android but I’m currently being cyberstalked and have reason to believe I have RAT (Remote Access Tool) malware on my home networked machines, phone and ipad.Some of these RATS are known to repopulate themselves to unsecure devices connected to the network that its on. For instance Smart Speakers, Smart Cameras etc. I know that a conversation i had with someone was heard by what i think is my Sonos Move 2 but i have no way of knowing for sure. So i am ultra paranoid.So far i have purchased a new laptop, new iphone with new sim and number, new router and now a new sim card as i use a 4G router. I found out all of these can share a RAT infection if they are on the same network given the right RAT Software.I have a lot of digital accessroies one of them being the sonos and im reluctant to get a new one if i dont have to, Can anyone difinitivly tell me if its possible for one of these
I got this issue while trying to add a new device via your application. An alert display that "There was a problem checking for updates." and I tried again but it didn't work. It showed another alert that said "We couldn't update your products. Check your network connection and try again later."
Ok so like lots of people the new app has caused havoc. I have 1 Play 5 gen 1 and 2 Play 1 speakers.Im trying to run them all on S1 as the Play 5 can't be used on new app.I have done the followingdeleted apps factory reset all speakersre installed both appsset up Play 5 on S1 app - this works fine Both Play 1 speakers are visible however I get the message that says that the firmware needs downgrading to s1 . I have gone through the process every which way. Whether having the speaker wired direct in to router or running it on wifi it just comes up with a message saying there is a problem and gets stuck in a loop of trying again, connecting app to speaker network then trying to downgrade. Nothing seems to workAny thoughts people ?
HiI’m still very, very, very mad at SONOS for the ******** they are putting us customers through with the new app and the way they communicate. I wish they’d roll back to the old app. But I know nobody at SONOS cares.Anyway. My Music Library (on my MacBookAir with OS X) works on SONOS for Mac OS X. However it doesn’t appear on iOS iPhone.Same at my mom’s house. She has her Music Library on a NAS (WD My Cloud, set to SMBv2). The music library works on her Mac Mini on SONOS for Mac OS X. However it doesn’t appear on iOS iPhone.Is it just us or hasn’t SONOS fixed Music Library for iPhone iOS yet?Anything I could try to make it appear?I already wasted hours (thanks SONOS!) trying different things. But nothing worked. Systems are all up-to-date.
I own a number of Play One and Play Three devices, plus one Era 100 that I bought specifically to add Apple airplay functionality to the system. Until quite recently, whenever I had all my devices grouped together in the Sonos app, I would be able to go to Spotify, select the Era 100 device as a target for AirPlay, and music would play on all devices simultaneously. Now, however, whenever I do the same through Spotify, only the Era 100 device plays, it gets kicked off the group, and the other devices remain silent. if I go to group the devices together in the Sonos app, nothing happens.this is a serious problem for me, especially considering that I bought the extra era 100 device specifically to be able to use airplay on the system. I’m not interested in using the Sonos app to control my music, and I am not interested in using the open play directly to Sonos’s group” functionality on Spotify due to reliability issues.
In Sonos App the battery level percentage is no more shown. How can is it possible? Thanks a lot for help
I have had issues with Sonos and the new app updates for a year now. I finally persisted in ringing ‘Christina’ tonight. We removed stereo pair in the lounge, the Move and the Sub. These were then merged with the Sonos Arc and diagnostically tested each time. The Move was glitching with the system and is not meant to be used in a ‘cinema’ environment. I can now manuaaly merge if I wish but it might still glitch the system. The router Channel problems were linked to me using the Sonos Ones as a ‘stereo pair and NOT surround speakers. So, I selected this and hey presto all is well! The S2 app has disappeared from my MacBook Pro though? And, there’s no replacement app there presently?! Magic powers.
Does the Sonos Line-in adapter transform the analog signal to a digital signal before delivering the signal to the speaker? Thanks for your help. :)
De speaker wordt niet gevonden, wie weet raadt? Moderator edit:Google Translate-The speaker is not found, who can guess?
Curious what this loudness setting does?
Buongiorno, vorrei qualche informazione in merito alla compatibilità tra sonos ARC e il giradischi project T2 w. Moderator Note - Translation by Google:Good morning, I would like some information regarding the compatibility between Sonos ARC and the project T2 w turntable.
Plugged in two wireless chargers for the roam 2 today and the chargers led is blinking red and not charging. I am using the adapters that comes with the chargers.
I have a Sonos Arc - when it arrived both of the oval caps at the ends of the speaker were slightly loose. When I tried to reattach them they completely detached. I am unable to push them back in and properly secure them. Any ideas or solutions?
Wie kann ich die Ansagelautstärke meiner Sonos one regeln? Moderator edit:Google Translate-How can I adjust the announcement volume of my Sonos one?
I recently upgraded two One speakers used as surrounds in my living room to two Era 300 speakers. The Ones have been factory reset and removed from system. I installed the Era 300 speakers in the same positions as the previous Ones and connected. When I try to add the Era 300s as surrounds they are not an available choice. I can only find other Ones I have in the house as well as my Amp. All updates are complete, app is the most recent, and the Era 300s are not in stereo mode. I've removed Sub and tried to add Era 300s and still nothing. The only thing I haven't done is factory reset the Beam. It doesn't really seem to make sense. Any ideas?
Hello,Can someone please tell me if it’s possible to connect a Sonos Roam 2 to my Xgimi Horizon videoprojector via bluetooth and then connect the Sonos Roam 2 to my Sonos Ray Soundbar via wifi and the phone app. That way can I have the sound from the video projector on the Sonos Ray Soundbar AND maybe the Sonos Roam 2 without any delay? I’ve attached a drawing to explain.Best,
Sonos One can play music from my phone, can command Alexa to provide weather etc, but when I ask ask Alexa to play radio station (eg. Radio 4), it replies “playing radio 4 (or Times radio or whatever) but then there is just silence. I have just changed my router but presumambly that is ot the problem as Alexa reponds, but it just doesn’t play the radio stations.Any help would be appreciated.
Hey all, hoping somebody has some tips to troubleshoot this really odd problem I'm having since swapping out my Arc for the Arc Ultra soundbar.I've been trying to troubleshoot this all day and feel like the culprit of the issue I'm having is the TV. Here's my setup:LG 65" C1AppleTV 4KXbox One Series XPlayStation 5Sonos Arc Ultra (plugged into eARC port)I noticed that when I swapped out the Sonos Arc to the Ultra last night (where I literally just swapped it out; using the same HDMI cord which always worked perfectly with the Arc), suddenly my Apple Music wasn't playing in Atmos and my Netflix was playing a show that I know supports Dolby Digital 5.1 was only showing in the Sonos app as Stereo PCM.I did a lot of troubleshooting today, and unplugging and plugging back in of cords, etc. I feel like the issue is with the TV changing the signal from the eARC port somehow.I think this because I just did a full unplug of the Arc Ultra power cord and HDMI, and also unplugged the HDMI cord from
I can’t control any of my speakers weather sound or channel so bad looking at removing my 12 Sonos speakers help please
WHen I update my music library (which is mainly held in Itunes - copies of CDs, playlists etc), the Sonos desktiop app now creates duplicate ‘playlists’ - although each new version is not necessarily the same as the original or even (in some cases) even remotely similar. I tried updating a couple of times before I clicked that each time I updated the library another random duplicate-which-isn’t-a-duplicate would appear, so my music library is now a disaaster area and even less use than it has been since the May Outrage.I see that somebody raised a version of this query three monthsm ago and got a ‘best answer’ from SOnos of (1) we know it’s a problem from 16.3, and (2) we don’t know when we’ll get around to fixing it.I’ve pretty much stopped using Sonos at the moment, so I haven’t been following the update management. Is there anybody still there and are we still expecting our systems to work again as they once did? Is there a work-around useable by anyone other than IT professional
I have spent hours, tried EVERYTHING suggested to fix the 1101, 1000, and 30 error codes when adding a new Sonos One SL speaker to my system. I have tried the solutions repeatedly, and nothing worked …. UNTIL - i went to my router settings; i checked the list of devices on my wi-fi and found the problem - the Sonos Roam that i had added months before was stuck on the list as a ‘paused’ device on a 2.4ghz frequency. I set it up using 5ghz and it worked fine; the problem was when i tried to add a new speaker (One SL) it would not update no matter what i did i could not register it - until i unpaused this old install remnant roam device that i didnt even know was listed on my network (all were unplugged, this was still there). When i unpaused the phantom device on my network and tried to register the new device for the millionth time again, it worked! I had powered on just the roam and one sl, all other speakers were unplugged; i had rebooted the network; i had unpaused the non-existant d
I use a Sonos Beam and notice significant differences in volume when switching between channels. Is there a way to set a general output level to avoid these variations?
Bonjour,Je souhaite changer le réseau wifi sur mes 2 amplis Connect Amp 1.Sur l'appli, le nouveau réseau apparait, mais on me propose uniquement de l'effacer, pas de s'y connecter à la place du réseau actuel que je souhaite changer. Merci de votre aide
Already have an account? Login
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.