Components & Architectural

Hi,I have 7 sonos speakers and 1 Amp. All are physically connected to an Ethernet port of my switch.All the Plays are in Disable Wifi mode but I can't disable the Wifi for the Sonos Amp, the option is grayed out.Any advice ? 

Having a party and switched off all of the speakers except one.  When I tried to then add the others back, they showed check marks in the app as if they were connected, but no music playing, and were grayed out.  Tried rebooting app, using another iPhone to control, using my MacBook to control.  Nothing.  Party had to continue with no music.  I spent a fortune installing speakers, turntable, soundbar, multiple amps.  Am soooo frustrated!

Have 4 Sonos ports as part of a media system wired to play throughout the house. Music Appears to playing from the Sonos app, yet no sound in the house. All ports and plugs have been checked and reset. They are green, so all appears properly connected. Any suggestions to fix?

Morning allI’m not sure if this is an extreme use case, but please hear me out: I have a turntable and streamer+DAC combination connected to a headphone/pre-amp analog-in, which in turn has analog outputs to a Sonos Port. This is fine for listening to either digital or analog sourced music through my Sonos speakers, wherever they may be.However, I also have a set of passive speakers connected to monobloc amps (1 amp per speaker, L&R) and I was wondering if I connected my monobloc’s to a Sonos Port (potentially one Port for each monobloc), could I in theory send an audio signal from the Sonos Port connected to my headphone/pre-amp, wirelessly to the Port’s connected to the monobloc’s, these Port’s acting as a preamplifier to the monobloc’s, thereby allowing my passive speakers to effectively be active speakers, but of somewhat higher quality than a Sonos smart speaker?I am of course presuming that the music signal is at least CD quality/lossless and not compressed and that the Sonos

My Sonos amp that I use to play my record deck keeps disappearing out of my system   I re connect after had re set then it shows but then goes again.  Any advice ? 

If I connect a DAC vía cable to an era 300, but I have 2 era 300 , how do I play música on both?

Hi,I have a Sonos amp connected to my TV via an Hdmi arc cable. When watching tv, the sonos amps always turn on and use the external speakers. Even if I change the audio output on my tv to tv speakers, it switch to external speakers after 2/3 seconds.It is due to the fact that Sonos amp cannot be turn off.  Is there a way to not use the external speakers when watching tv ?  

Hi - I am still running my system on S1 without many problems.  Lately, though, my ZonePlayer 100 is disappearing from the network.  I think I purchased the unit around 2005, so it might just be dying...however, it comes back into the visible zones and plays music every time I power the unit off and on.  Any ideas for things to try to make the problem stop recurring?  Thanks, David   

Hi,So I have a turntable connected to a pair of Sonos 5 speakers and the system has worked just fine for over a year. This morning I was listening to a record and went to turn the volume up via the app and when I hit Apply, the sound cut out completely and now I can’t hear anything. I’ve shut down the app, uninstalled and reinstalled it, checked all the settings but nothing has worked. The connections are all fine and literally the only thing that’s changed was hitting that Apply button.   Does anyone have any idea on what to do as I’m beyond annoyed at this.    Thanks. 

I have an assortment of older Sonos speakers and I was wondering, what component/s do I need to add to connect directly to my Wi-Fi network?  I’m currently using two Sonos bridges atm.  

Sub Gen 3 doesn't power up.  It makes a noise as if it is trying to boot but does nothing else.  There is an odd smell created as well.  In addition the power light does not illuminate.  It also cannot be discovered by the app.  It used to work fine and then it started doing this.

I have lost one set of in ceiling speakers in one room. They have just disappeared from my app.

Hello,Currently doing electrical remodel for a customer and dabbling into speakers as i have installed sonos amps and speakers for customer but this remodel has me hesistant. As this customer wants to use existing speaker throughout house. The house has over 22 speakers which each room has a a wall volume control as two speakers in each room will run to volume control then ran to media center in living room(speaker wire 16/4 and ethernet). I want to split house into 6 zones, listed below. Basically asking could i just have the wire ran from volume control wired straight into the amp or would i have too disconnect volume control(outdated i believe) and run new wires from each speaker to new amp?Trying to avoid running new wires to existing speakers, but am fine doing so if needed. Just confused if I’m over thinking and the volume control is just something that can coexist and use the speaker wire/ethernet ran back to the media center. Living room(4 speakers)Kitchen/Dining(4 Speakers)Bed

I have a Sonos amp connected to 4x Architectural ceiling speakers and a Sonos amp. The speakers work quite well but lack a little bass. As soon as the amp is added to the system, the equaliser and fader no longer work. 

Looking for guidance.  I still have a cable box through Xfinity to provide my cable service.  I have surround sound in my main room through a Yamaha receiver which is connected to my port.  However, through my kitchen, foyer, and other rooms i have a combination of Sonos 5’s and Sonos One’s.  Typically on a Sunday when NFL is on, i like to connect the main room, and tie the speakers in the kitchen and other areas of the house to hear the game i’m watching.  When the season began, i went to connect all of the speakers together, and the option in my Sonos app for “Line IN” or “TV” was gone.  I spent the next two hours on the phone with support.  We reset the port, we deleted the app from my phone and reinstalled it, nothing would get the option to connect the speakers together through the surround sound.  Regular streaming music was fine and could be played to all of the speakers.  This would elude that the port was working.  This happened to me in the past, but was resolved when an upda

I am trying to add a boost to my network. All my stuff is S1 and it says boost is incompatible but I have read that it can be added with S1 app. How to go about this?

I have two pairs of in-wall Sonance Architectural Speakers wired to an Amp. I have had no difficulty in the past detecting them. There are no other Speakers wired to the Amp. The detect function no longer works. Is it possible th as that I have mixed up the polarity of the cables?

My Patio setup with Amp and Polk speakers won’t connect with any other rooms.  I can play music through the Patio, however, it won’t sync with other rooms even with the Patio next to the living room.  All other rooms can connect with each other without issue. I’ve reset the router, disconnected the power to the Amp, shut down the App.  Nothing seems to work so far. I submitted a diagnostics: **********Moderator edit: recorded and removed diagnostics number

I installed 3 new sonos amp for my customer upgrading from their existing S2 sonos connect amp setup as they wanted to use airplay 2 features.after setting up the 3 x new sonos amps I tried to use one of the old sonos connect amp for an additional zone powering 2 x speakers. i factory reset the old connect amp and It initially allowed me to add to the new system but then kept saying that the connect amp needed to be added and would not complete the process and error message unplug power for device reconnect and try again. After several attempts i decided to remove and test back in my office. I factory reset the Sonos connect amp and have added it to a new system with 1 x sonos move. It seems to have added to the system fine and i can play spotify to each of the devices but if i try grouping them together it will not complete the task and error message unable to connect please try again later. Any help or guidance on this matter would be appreciated. 

I have a second hand Sonos Connect which I would like to add to my Sonos One speakers to play CD/DVD from an old music system.When trying to add the Connect it tells me it is not compatible, I have tried the S1 app but it always wants me to upgrade to the S2 app. Is there a simple way to do this. i am 70 years old so a simple explanation of how to get this working would help.Many thanks in advance

I have a pair of powered bookshelp speakers (not connected to a reciever). Can I hook them up to a Port and stream using the Sonos app?

I’m a Sonos novice.Using a setup with three zones.  That part seems to be working fine.However, I’d like to add one non-standard setup through the HDMI AMP input (RCA already works for this setup, but 75ms latency is too long, so not an option).  I’ve seen the digital/HDMI input is supposed to be much lower latency.I want to be able to speak/sing into a microphone and have it amplified through that HDMI input.  Not loud, just maybe 70-75db range.  I connect a microphone to a Zoom U44.  Then I take its optical output, use the Sonos optical to HDMI converter (with an additional HDMI 2.1 cable) and go into the Sonos AMP.  Getting no sound, unfortunately.I believe the Zoom is outputting audio when trying this method because when I connect it’s digital output to an entirely different system it’s working fine.I know this idea may seem like more trouble than it’s worth, but would like to be able to test out and find out for myself if this can do what I’m hoping for.If you have additional idea

Hi,I’ve just bought some old 1st gen play 3 and play 5 speakers. The previous owner had cut the plugs off and had wired them up for use in France. The speakers now have no plugs at all. Can I simply wire a standard UK 13 amp plug to the Sonos cable and use that?Thanks

I just recently added Port to my Sonos system so I can connect my Denon receiver and Boston Acoustics speakers to my Sonos system. The “line out” function seems to work as expected - I connected line our from Port to aux audio input on my receiver and can now stream on my old system concurrently with my Sonos speakers.  I would also like to output from my receiver to the port and out to my Sonos speakers throughout my house. I have not been able to get this to work. I connected an audio out on my receiver to line in on Port and got no sound or very weak sound on delay. It seams like this should work. Based on product description, it seems like Port should be able to broadcast audio from my receiver to the entire Sonos network.   I called Sonos phone support and they said Port can’t do this. I don’t believe this is correct because under line in in the Sonos app “receiver” is an option. Does anyone have any help for me with this problem?  Thank you. 

Hi guys, I just bought a new Amp for my office. My phone can connect to Wifi normally, but when setting up Amp at the password entry step, the App says I entered the wrong password.I have consulted with the articles about Sonos system requirements and I have met all of them.https://support.sonos.com/en-us/article/sonos-system-requirementsI have checked in the router, my phone uses data normally, Sonos can also connect but cannot receive IP. Can anyone tell me what this issue is and how to fix it?