Components & Architectural

We lost power awhile ago and now our connect amp doesn’t work. We have reset it. The lights don’t light up on it. Think we need a new one?

Hi everyone,I have the Sonos amp and 4 Sonos ceiling speakers in our kitchen. The same amp also runs the Sonos sound bar and 2 One SL speakers in the living room.Every so often when I play playlists through the amp from my Amazon Music the songs stop suddenly after the first 15/20 seconds and move on to another song. At first I thought it was a preview of each song that I needed to turn off in the settings but then I realized that isn't the case. Is extremely frustrating having spent so much money on what you would assume is a quality system for it to be intermittent and ultimately so frustrating I turn it off.Another issue I have is sometimes my two one SL speakers cut out so I lose surround sound half way through a film and then they suddenly start working again off why I opened the app to see what's wrong.Just for context everything is quite close to each other and I have really good full fibre internet speeds and a good WiFi service within the house. Can someone please give me some

In a house with 5 amps, one zone plays music on its own randomly.Why?

I want to use Sonos Amp for my hi-fi-speakers but need more power than the amp supplies. Is there any way I can put together two Sonos Amps for the same set of speakers and thus “doubling” or increasing the power? Thank you in advance. 

Samsung Frame TV connected to a Playbar and Sub in my living room.  Works fine if playing from the TV or other SONOS sources.  2 Speakers connected to a Connect AMP (with 2 speakers) and configured as surround sound for the room produce either no volume from the TV or it’s so low I can’t tell if they’re working because I hear the sound from the playbar and sub.  If I pull the Connect AMP out of that room and set it up as a separate room both speakers are loud and clear when playing any SONOS source other than TV.  Why would that be? How can I get these speakers to work as both surround sound and when playing music from a SONOS source.  

I have a setup with an Arc, Sub, and 3 Amps.  1 Amp for the in-ceiling speakers in the room with the Arc and Sub (for TV), another Amp for outdoor speakers, and a 3rd Amp for speakers in another room.  I want to add a Turntable and CD player (long story on why we can’t just use streaming).  If I connect the Turntable to one Amp, and the CD Player to another will I be able to select the line-in from either Amp and choose to play that input wherever I choose?  For example, if the CD player was connected to Line-In for the Amp powering the outdoor speakers, could I use that input and play it only in the 3rd room, while simultaneously playing a different input through the outdoor speakers?  Does that make any sense at all? 

I have a sonos amp and in ceiling speakers in my gym and am wanting to run the treadmill audio through the speakers.My treadmill has Bluetooth capabilities, so I purchased a Bluetooth receiver and connected it into the Sonos amp rca in line.The treadmill connects to the Bluetooth receiver, the Sonos app says the inline is connected in the amp settings, but I have no sound.Any thoughts?

Hello,  My Sonos Connect has worked perfectly for quite some time. This week it changed completely. It disconnects all the time. Nothing in the setup has changed. Several times I've resetted it and moved it to different places.Everytime it starts again (after resetting it to factory settings) for a couple of minutes, than it disappears from my network. Since I've got it for my turntable, I can't hook it up physically to my router.I've spoken to the helpdesk on several occasions (I can hardly understand them due to the accents on their speech) and messaged on several occasions. It's getting to be very frustrating. My file number here at sonos is ********. Moderator edit: Case number recorded and removed

It happened again. The new update in Jan, 2025 dropped the connect 2 from my devices and I cannot reconnect it. I can occasionally get it to connect, but then it drops and I get a ghost image saying it is “Not Connected.” I am certain that Sonos is pushing people to buy other newer devices because it is ALWAYS an update that knocks the Connect 2 device out of the group. A new device is EXPENSIVE so please Sonos, do the right thing and continue support of your older compatible devices.

Hii I am looking to connect a pair of Sonos ceiling speakers and a single stereo ceiling speaker to the Amp…can anyone help with this please?  

I’ve been a long time Sonos user, but only recently installed a whole home AMP driven system (rather than just plug in sonos speakers). I’ve heard a lot of the complaints about instability of the new Sonos App, but hadn’t experienced it much till now. Wondering if there is a solve, or diagnostics I can share with Sonos to help them stabilize the new app. I regularly group 4+ zones throughout the house and it regularly stops playing and when I go back in the app, the entire group is disconnected, each zone shows “no content”, and need to be regroup the speakers and select a content source. Am I experiencing what many have been complaining about? Either way, this is sad as hell. Previous generation of Sonos was stable and reliable. This is disappointing.Sonos team, reach out and lets work together to get this solved.

my Sonos connect will not show up on my iPhone 15 in the original Sonos app

We have a Sonos sound system that has six amps which power speaker zones around our house.  For some reason, the speakers on one of the zones randomly disconnects from Sonos on occasion and we have to wait a while for Sonos to recognize it again before we can use them.Anyone know why this might be happening?

Hello, dear community. Can I have two PLAY:3 serve as a front (and only) speakers for AMP? So I can stream music by AirPlay to PLAY:3 via AMP or connect turntable to AMP and PLAY:3 will be the only speakers to play the sound?In SONOS app I can see that I only can add sonos speakers as a surround, not front. Thanks.

I have connected a Dual turntable DT 210 (with a working build in pre-amplifyer) and a Sonos Port (Line in) but i can't get it working (no sound). What am i doing wrong?  

I have an old first gen Sonos system.  Play 1,3 and 5.  I still use the Sonos S1 app.  I also use a Sonos Connect to listen to Sonos on my home stereo system through a pioneer amplifier and Bose speakers.  This all works well. I want to listen to my turntable and cds on the rest of my Sonos system, not just on my stereo system and Bose speakers. I know I could plug the turntable or cd player directly into the Sonos Connect to the analog Input, but there are 2 problems with this.  First, there is only room to plug one of them in, and second this would mean they were not plugged into my stereo system.  So, my question is, how/can I have these components on my stereo system through my receiver and also be able to have them extend through my Sonos.  Any help greatly appreciated.   

Hey guys.Today my Sonos Port underwent an update. And after that it didn't connect anymore, even my account seems to have disappeared.I've tried every possibility listed in the Sonos help file and nothing works.Any other suggestions? 

After searching threads on this site, I am STILL unable to successfully play radio output from my Yamaha receiver, (RX-V373) via a Sonos Connect (S15, Gen 2 mfg 05/2019), to play through my Play:1 and/or Roam SL speakers.Once I get this working, I’ll hook up my turntable (unamplified) and CD player to it.Here’s a photo of the back of my receiver. I have tried RCA cables connected to the Audio Out jacks (lower right hand corner of the photo)In each case, I’ve connected them to the Analog Audio “In” jacks on the Sonos Connect. My Overall System has 3 components:Living Room: Play1Living Room: Connect (Model S15, manufactured 05/2019)Living Room: Roam SLConnect menu shows the Line-in is connected.The Line-Out only has a choice for Line-Out Level (I chose “variable”). I’m clearly missing something crucial!Thanks! 

Sur un sonos CONNECT ( modèle indiqué sur l’étiquette au dos de l’appareil  ) à quoi servent les entrées Audio IN et les touches de volume ?What’s the of analog inputs and volume control on a Sonos CONNECT?

I have great difficulty playing CDs through the port, and cannot play cds without the port. Does anybody have any suggestions?  It is an old system Yamaha amp and Rotel CD player. 

Hello!! I’ve been a Sonos user for a while now but have a few questions regarding my amp. I have a home system with multiple Eras (100s and 300s), One SL, Play 3, Move, Roam and a pair of Klipsch AW 525s hooked up to a Sonos amp. After doing some research the Klipsch’s are 8 Ohms with 75W of handling. I’m a looking to add another pair of speakers to the amp but am wondering if I can do with a pair of 100W 8 Ohm speakers. Can I do this or would this be to much for the amp to handle and would I have to get a separate amp for this?

I am a little concerned about all the posts that talk to the 75ms input delay.  That may be the major issue throw my way as a deal breaker but I thought I’d still ask.I have an old ZP120 amp. We do a bit of karaoke at home with a little speaker with colourful light (kids love it). However, we can't get enough microphones connected for a decent singalong. My thought was buying a 4 way Bluetooth microphone mixer (with 6.35mm output jack), that I could connect with a 6.35mm to RCA cable, and plug that into the Sonos amp with speakers plugged in direct. We'd use TV to play the karaoke itself (music and lyrics) separate to this setup (alongside a disconnected whirly disco light). No use of the S1 app, just connectivity. Does that sound like it would work or does someone see an issue?

I cant connect my sonos connect to my system..I try to reset it ,   my sonos is always searching and it never see it 

Hello Everyone, just bought a Connect Amp Gen 2,  I wanted to confirm the boot sequence to check I don't have one on the way out. My previous G1 connect amp started flashing the white light as soon as power was applied, and finally staying solid once connected. I expected the G2 to do the same, this time when power is applied, the white light comes on solid for 3 seconds, then goes out for 20 seconds, comes on again flashing until connected then Solid. The 20 seconds with no light is very consistent, so am hoping this is normal ?. Can anyone confirm this is the same on their G2 connect amp pleaseThanks very much 👍  

Hi,I have an old S2 Connect Amp and 2 x 8ohm speakers, i though i was smart so i combined one of the speaker leads from each speaker and so on the connect amp on the speaker output both blacks are connected together and then separete L and R goes to each speaker. The amp plays but cuts at 60% volume. Is this wrong what i have done ? Should i go back to separate black lead to each speaker ?/donib