Spaces & Setups

deseo saber si sonos AMP ha tenido diferentes referencias con el paso de los años o si es única el modelo y referencia actual. Esto con el fin de no ir a comprar un producto obsoleto 

Hello.  I have a Sonos Arc, Sub and 2 ONE rears.  I have no problem with surround sound coming from the rears using the TV (2.0, 5.1 or Atmos) and other devices eg mobile phone.  However, when I play a DVD through my Sony 4k Blue ray player, I don't seem to pick up much sound through the rear speakers even when the DVD I'm playing says 5.1 surround etc.  Am I doing something wrong?  Thanks. 

I have a Sonos system which generally works well. Recent bad weather has resulted in several drops of mains power , sometimes for a few seconds, sometimes for a few hours. The result is always the same. I have some radio sources permanently attached to each speaker - so for example the Sonos ONE in the ‘Dining Room’ has my favourite radio station permanently connected; the speaker is simply turned on and off via the top button on the speaker.I have several speakers in different rooms similarly setup in the same way.After a power outage the knowledge of which radio station connects to which speaker is lost and has to be setup again.While this is ok for me, being relatively familiar with the Sonos app I have to say that my wife - aged 80 - and with little technical skill in the system would, if left alone , be frankly unable to sort it out, rendering the system useless.Surely this product cannot be aimed purely at tech savvy youngsters.  Surely it is not beyond the wit of man to create a

Has anyone noticed a metallic/tinny/robotic sound from their Beam since the recent update?

I hope an update is coming because I’m over going to use my roam and it’s dead. Out of the five times I’ve wanted to use it I have only been able to use it once. I have to leave it on the charger when not in use otherwise it will be dead when I go to use it. When it’s on the charger and it gets to 100% there is no way to turn it off. If I hold the power button for five seconds it turns off but within a few seconds it turns itself back on again. If they don’t say a fix is coming within a week sadly it’s going back.

I have my Sonos system with Spotify Password saved on it.I now would like to create, for my office separated from my house, another Sonos account using the same configuration, including Spotify. But I do not remember the Spotify pasword that I used.Is there any chance to get the saved password from Sonos Controller / App ?many thanks.

I have both a sonos s1 system and a Sonos s2 system. All the connected S1 components show up on IFTTT but not the S2 components. How do I get both the S1 and the S2 components to show up on ​​​IFTTT

Anyone else pissed that Sonos doesn’t include a power adapter w/ the roam?   Before you tell me that everyone has a bunch of extra 10v adapters lying around the house, I’ll tell you that I don’t.  

Hello,Love Sonos for 10+ years. The ability to set a schedule for night sound would be a big, simple improvement. It ends up getting left on accidentally. If anyone can influence that I would appreciate it! Thanks. 

No poseo iphone ni dispositivo con ios, y mi pregunta es si pido prestado uno y configuro la barra con trueplay, y despues desenlazo con ios y sigo utilizando android, se queda configurada la bara?, gracias 

Album art disappeared after Sonos update, my music library is on a WD my cloud mirror and has been for over 5 years using S1 & S2 with no problems but after Sonos update lots of art work was missing Sonos advised me to remove my library and reload it, still lots of art work missing but now lots of albums are indexing wrong ID tags have been perfect for 10 years with Sonos all correct in iTunes and Windows 10 but Sonos splits albums that have been correct for years after speaking to Sonos they can’t help and they don’t know why it is doing it any help please.

Hi I’m curious what people think of the mini controller ? It can be displayed in two windows sizes but I find both sizes are too big and much unpractical because it always lay somewhere on your desktop and will eat on your other apps. I wish it could be minimized neatly in the task bar with just the volume and the cue forward / backward or back / next buttons. No need to display the album cover picture this eat too much space. Anyone think the same ?

I have a sonos playbar and a sonos beam. I want to send the signal from the tv to the soundbar that I select. I do not want to split the signal between both I want to choose which soundbar I send the sound source to. I have looked for a toslink switch (playbar does not have HDMI) that would be one in and then select via a remote either sound bar but I have not been able to find one. Everything I find the switch selects the input and sends it to a single output. Any thoughts would be greatly appreciated

There’s already a conversation for this, but it’s a few years old.It’d be really neat if we could customise the crossfade on Sonos - ie increase/decrease the crossfade length, and (this is maybe a stretch goal) enabling it for some playlists, while disabling for other playlists. I find the current crossfade length isn’t really useful, and would love to be able to increase it :)

Question  withdrawn 

I'm fairly certain this has been discussed before, but I need a definitive answer.I have an Arc w/ 2 Ones acting as rears for surround sound that are connected via ARC (not eARC - the TV doesn't have it) to my 2017 Samsung Series 6 (model no: UN55MU6290) which is also connected to my PS5.Notably, my Samsung does not have an eARC connection. I think this may be the culprit.On my PS5, I have the following config: HDMI Device Type: AV Amplifier Number of Channels: 7.1 ch (issue also occurs when on 5.1 ch) Audio Format: Dolby On my Samsung, I have the following config: HDMI Input Audio Format: Bitstream Digital Output Audio Format: Dolby Digital The Sonos app is telling me that the Audio In is Dolby Digital 5.1. This is great, but there is a .5 second delay upon input and sound output. All other apps I run through my Apple TV 4K have zero delay and sound great.My question are: Is my TV too old and not powerful enough to process all the data for PS5 audio in a timely manner? Am I mi

I just wanted to add my experience to what has been posted before.  It took some time to get to the bottom of this and the previous post was a little short on detail.Inputting from Sonos Connect is relatively simple, using one of the RCA input socket pairs and relabelling the Input on the Denon to Sonos. It was the output that I struggled with and at one stage Denon staff told me that this was just not possible.  I have used the Zone 2 Pre Out RCA sockets and the Connect RCA input sockets as the connection route.   The problem which I had failed to detect was that the signal coming from the Pre Out is very weak.  This can be fixed using the following steps on the Sonos App:- Go into Settings/System/Products and the Room where the Connect is used. Within this there are a number of sub headings including Line In.Within Line In there is something called Source Level.   As the Denon acts as an AV component I used this setting which is Level 2 when in fact the signal is so weak it needs to

When is Sonos going to update their software to sync in L&R front speakers to their surround set up? 

I know most of the people will say , get harmony remote , use the Denon app or even smart plug but i want to be able to turn on my sonos port via the sonos app and make my denon turn on and set it up to the right input (CD in my case) automatically . trying to convert 12V trigger (from sonos port) to IR command (to Denon receiver) seems to be challenging and the only project i saw requires you to be an engineer. I finally tried to look into HTTP commands and saw that Sonos support IFTTT but only as “That” part in the code and you can’t create any macros or scripts that will trigger if the Sonos port is on. Here is my question: Anyone here knows how to build raspberry pi server which will be able to “listen” to local network and once the sonos port turns on it will execute a simple HTTP command to turn on the Denon?

Purchased a Sonos Arc, Sub and two Sonos Ones for surround sound to add in addition to my Vizio 75” V Series TV and the Apple TV 4K (latest edition). Since I purchased this I have had intermittent sound issues with different apps on Apple TV (Hulu, Disney+, HBO, Netflix, etc) that has the sound stay on for a bit and then cut out for a period of time then come back in. I called support and they were no help. It’s discouraging as I paid almost $2k for the Sonos products and am not able to get the full impact of it. To give some information, the Sonos ARC is hooked up to the TV via HDMI not through the optical cable option. I have switched out the HDMI cord and that did not help. Latest support diagnostic is: 841974370

I’d like to see the ability to switch to a more basic controller interface. One where you can simply select the room and music on one screen. I never look at the screen, don’t care about the skins and all of the rest of the stuff. I made my playlists already so I know what’s on there. All I want to be able to do is pick a room(s), select a stream and set the volume. This would just be the ability to switch between a basic remote and a full controller. 

Hi everyone,a few days ago I bought a Sonos Arc and I completed my 5.1 setup (I already owned a pair of Ones and a Sub). I am very satisfied with the general quality of the audio and I have already performed the TruePlay procedure using an iPhone 13 Pro. The only problem is that the central channel, relative to the voices, is always a bit low. I tried to redo the TruePlay tuning with another iPhone (7) and also to redo it focusing on the area where I sit to watch TV, but the situation changes little to none. Arc is connected to the tv via eARC and the tv passes the dolby digital signals correctly. Why Sonos, despite all the requests from the community, does not allow us to adjust the center channel volume?The NightMode and Speech Enhancement functions improve the situation, but they are only palliatives that "ruin" the overall equalization. With the old system I owned, I could adjust the volume of the center channel. It was enough to set it to +3 to solve the speech comprehension probl

I know this has been mentioned multiple times as a feature request in a multitude of different ways but I wanted it brought up again as the Alarm functionality is not robust enough. Certain things can be done using multiple alarms. The biggest thing I am looking for is multiple room/device functionality with alarms. I have a Move and two Play Ones in the Kitchen. I also have a Roam in the Master Bathroom. I would like all three sets of these devices to play at the same time every morning. The problem is that I have 3 alarms and more often than not they are all out of sync even though they are scheduled at the exact same times. The include grouped room function does not solve this problem, I am not sure what it even does as we change room groups so often. The solution is simple, instead of that include the ability to choose room groups as an option. They already exist and are easy to create and use plus then they would all sync up. Or, just add the ability to choose multiple rooms under

Everytime when my wife wants to connect to sonso roam with bluetooth it just does not work.Sometimes when the device is off it starts automatically and no worries, but more often even when the device is on, the bluetooth on the phone tries to connect but no response what so ever. I have to stop and start the sonos several times and all of a sudden it connects.What I described is exactly the same patern that I must follow to get the thing working.just try over and over again until it reacts.It is really annoying that she up until now is never was able to connect with out my help.She has no issue with all our other Bluetooth devices so she knows what to do. (Just click on the devices name in the bluetooth menu)I am worrying I was unlucky and bought a faulty device.   

I believe every audio device should have a standard feature (or at least option) to fade in an out when you turn the music/speaker on and off. If you go over to a speaker and hit play or do the same on your app the volume should slowly ramp up to the level instead of instant on - you can decide what to do when you simply pause it but I would always prefer a fade. In addition, it would be even better if the system tracked speaker usage to determine preferred sound levels. For instance, I might always use a speaker at level 3 but the last time I used it maybe I cranked it for a really good song. A day later I’m much more likely to want it to start at 3 than cranked. This can also happen if someone else happened to use the system. It would be very easy to create some basic AI to track speaker volumes and use that to determine what to do on start. That in combination with fade in would make the system feel much more elite.