Components & Architectural

Recently bought a Port to connect a technics turntable.  It's been working great, but when I dont use it for a week. I cannot find the line-in on the Sonos app.I have already had to reboot the Port twice and it's a little tedious to do this each time.  Why is the Line-In dropping off?Any quick way to ping the network and reconnect? 

I have a Sonos one ?Can I add ceiling speakers ?if so which ones do I order ?please x  

I have a sonos system with 10 speakers wich works well. Until I connected two Era 300 as stere pair with a Pro Ject T1 SB lined in to the left. When I stream music the right 300 drops out and the whole system goes caos with soud dropping out in all rooms and sonos switching songs.. When I play a record on the stereo pair, the right speaker drops in and out all the time. When I spoke to Sonos they said It had to do with the setup on the router. Now I have forced the router to only use channel 6 on 2,4 and channel 100 on 5. With no luck. I have very good wifi speed all over the house. What should I do? Buy a new wifi6 router?

Anyone had similar issues with their Amp? Constantly emits a loud buzzing noise directly from the device, irrespective of lines in or connected speakers? So irritating I have to have it physically unplugged when not in use.

Good day. I have a system running 7 SONOS Port Media Players. Not attached to this account but another. The earlier Sonos app, S1 was used to configure and set up these players as a system, and the account signed in as owner, but after updating to S2, the account no longer lets me in as an owner. Is this a known issue? If so, is there a method around this besides starting from scratch and reconfiguring? Thank you.

Is it possible to connect my new tv with an HDMI e arc port to a gen 2 connect amp?

One of the connects is connected to my home theater receiver and the other is connected to a strereo receiver in another room with a turntable.  How can I get music playing on the line-in input to play on the other system?  Both are in the same group. 

I recently purchased a pair of the Sonos Architectural speakers. I noticed my Sonos amp purchased in 2021 does not have the ports to have the speaker wire connected to it.  I have the sonos amp connected to a Yamaha two zone receiver.  Will i be losing performance of the architectural speakers without the sonos amp having the ability to run the outdoor speaker wires to it?  Do i purchase a newer amp which will be able to provide more power to the speakers, or stay with the speakers being powered by the Yamaha receiver.  Presently, i feel the sonos outdoor speakers are underperforming.  They do not have the bass the other sonos speakers have.  

Hi I just bought from somebody arc and sub2 I do factory reset and arc working fine but sub doesn’t want connect 

Hello. I just received my Sonos amp with Sonos speakers. I was following the steps of first setup via my Android Sonos app. I got to point where i was asked to enter my home WiFi password so the amp can connect to it. After entering the password, the app shows a message saying ‘’Your Sonos Amp has been added, but may not appear in your System. If so, unplug the power cord and plug it back in to finish setup from System Settings.’’ The amp wasn’t added in the app so i tried to unplug the amp, then plugged it back in but nothing happens. It is still not in the app. I have tried to factory reset that but with the same result. Can anybody help? Thanks

I have a Sonos Connect Amp and while blowing dust out of the stereo cabinet the Sonos Connect amp fried. Opening it up I see a Lion power transformer is burned. Looking to repair with a Lion 1706, with a number 6016A0005701. Is this feasible? The internet does not find this transformer that is installed on the circuit board. 

I have an older Connect Amp connected to wired speakers in my kitchen. I have an old sound bar in my living room. Getting occasional cutouts in the kitchen when pairing the two for audio. Tried hard wiring the Amp but still experiencing issues. 

I have a Sonos Amp in my basement and it powers my Bowes 251 outdoor speakers attached to my Pergola. I would like to add a subwoofer underneath the deck. What is the best seamless option to achieve this?

I have a Sonos amp and have a kef kube sub. They have been working great but today the sub is cutting out after 5 seconds and my amp  is not picking up the sub on my app. I have tried updating the system without any luck. 

I just read on here that someone was having trouble with blown Sonance outdoor but the thread is now closed. So have to make a new oneI have a Beach Bar Restaurant & my beach area with all the tables is 20m x 20m 1 side being the sea and the opposite centre is a tree planning to mount high up 2 x Sonance outdoor facing diagonal L & R to the beach and the Sonos Amp. There is potentially the option to use another central tree about 8-10m from the sea which could mount facing the sea or back to the restaurant I can’t find any decent reviews of Sonance Outdoor online, and nothing to give a sense of volume available. I have 2 Era 300 which sound great so I’m presuming at least as good as those...It's a sit down restaurant (but lively) so music needs to be back ground music (people shouldn’t need to shout) with great sound quality, but with prolonged use - They will run for 14 hours per day every day.Now I see the thread about someone with repeated blown speakers and others recommend

I cannot find a code at the bottom to add the amp to my system.Is it possible to get a connection without the 6 code?

Good Morning,I recently purchased a SONANCE MAG6.1 System w/ a Sonos AMP that I’m planning to setup in my back yard / patio area. I’m having trouble with deciding on the best placement for the 6 speakers+sub.I was leaning towards just covering the patio area, but may also consider covering some of the other back yard areas as well. With only one AMP in my configuration, however, it seemed like that may not be ideal in terms of adjusting volumes for the different areas of the yard.Would appreciate any advice you have. Please ignore all the brown grass in the photo - just had lawn irrigation installed a few weeks ago.  

Hello, I just purchased a Port to pair with a Turntable I have (SONY PS-LX350H) with a pre-amp. I can barely hear sound out of my Sonos System with volume maxed out 100%. I have rooms of Sonos: Arc/300s/Sub, Fives/Sub, 100s/Sub. I can use them, but again really no sound. The Turntable does not have a Phono/Line switch. What am I missing here? Do I need the AMP? It looks like it just for non-Sonos speakers. Please help.  

I have an older turntable (Audio Technica AT-PL120) with no built-in preamp or ground connect. This connects directly to my Sonos Connect (Gen 2). It plays immediately but I have to raise the Source Level in the app to Level 8 or so. I was wondering if I was losing out on sound quality by doing this. Is this valid?As a test, I plugged in an old RCA AH500 preamp but it immediately created a loud buzzing when the music started playing. The buzzing only continued with the preamp. When I removed the preamp, no buzzing. The preamp has no ground connect either.I tried multiple RCA cables, so it’s not that. I figured it’s either an old preamp that’s not working anymore or I have to do something with the ground but I got nothing to connect it to. Any thoughts on this? 

I have a lot of older Sonos Speakers and a couple of newer ones. One newer one is a PORT which I downgraded to make it S1 compatable. Anyway I would now like to make the PORT S2 as I only use it on my HiFi and do not stream it to other devices. So I have managed to remove 2 Play 5s from my S1 app as part of the upgrade process but now I want to put them back. The SOnoS 1 app says I need to update so I cannot. The S2 app says devices incompatable or something. What is the quickest way to get my Port on S2 and all other devices back in S1. I seem to be stuck in a loop at the moment.

I have 2 Sonos Amps. One powers deck speakers (irrelevant, I think). The other powers Sonance 6.1 outdoor speakers around my pool. Both Amps are located inside my house. I am trying to figure out how to output audio through the pool speakers if I were to add an outdoor TV/projector. I really don’t want to drill more holes and bury more cable. Are there any good wireless solutions? I do have lots of access to power around the pool area, if that makes any difference at all. Otherwise, the amp is approx 35ft to first speaker and at least 50 feet or more from where I would place the video source. As another note, I live in a high humidity/high moisture/hot climate in the summer, so I opted not to use a “weatherproof” box to house the amp by the pool. TIA

ZP00 will not factory reset, only displays only amber light

I have just set up 4 Sonance VX60R speakers in the ceiling of my studio and want to optimize them with my Sonos Amp. The speakers are all wired correctly and there are no switches or volume controls. When I try to optimize the speakers on the Sonos App I hear the high pitched tone but receive a message saying “No Sonos architectural speakers detected. Any help optimizing this set up would be appreciated. 

At first I play side one of a vinyl record. Making sure to use the slider to set the volume. However sometimes when I turn over to side two, and press play, the volume goes way up to 100%, busting my neighbours eardrums 😃. Is it a known problem? Any fixes?

I have an analog turntable, without a built-in preamp, currently connected to analog speakers. I would like to connect it to our Sonos network. At the moment, we have three Sonos speakers without a line-in (I believe they are Sonos Play). What do I need to connect everything? Thanks in advance! The photos are of the turntable (hopefully to clarify)… —————-Ik heb een analoge platenspeler, zonder ingebouwde platenspeler, nu nog met analoge boksen. Deze wil ik graag op ons Sonos netwerk aansluiten. Op dit moment drie Sonos boxen zonder line in (volgens mij de Sonos play). Wat heb ik nodig om dit allemaal te verbinden… Dank alvast!!  foto’s zijn van platenspeler (hopelijk ter verduidelijking)..