Components & Architectural

I have a Connect Amp (ZP120) for a few months now. Basically works very well, very happy with it.But...Spotify Connect falters about once or twice an hour on average. Stops playing and continues where it left off after about 5 to 10 seconds, in the middle of the songQuite irritating. I read that I'm not the only one and I think I followed the tips from elsewhere. Removed Spotify as a service and re-installed it. As it happens during songs, it can't be Spotify-ads (I'm using Spotify Premium).Switching the network connection from wired to WiFi makes no difference either. No problem with all other connections to the same network.What else can I do to resolve this problem? Internet radio and playing my own content on my NAS work without any problems. Spotify from the Sonos S1 app also seems to work well, but is a lot less practical and user-friendly then the Spotify Connect.I'm curious if anyone knows anything that could lead to an improvement/solution. Thanks in advance!

Hi there. I have been experiencing sporadic audio dropouts across my system. I have 5 Connect:amps, and they are connected via ethernet to my router. This issue seems to occur fairly randomly across amps. Diagnostic ID: 1858171971

My Sonos system features a sound bar and sub, as well as a Connect Amp that powers non Sonos speakers wired into my ceilings. I bought a Fluance turntable and pre amp and got a Connect to link it to the system (it’s in a different room than the connect amp). When I play the turntable Through the sound bar and sub it sounds great. But when it plays through the wired speakers it skips. Sonos says the turntable requires a separate amp to power the non Sonos speakers. They recommended either an Amp or a Port to replace the Connect. But I’m wondering if I should just buy a used Connect Amp instead. Much less expensive. 

Hi,  I have a Sonos Arc and Sonos Connect Amp that plays sound from my tv. The arc will continue playing audio but randomly the speakers in my ceiling connected to the amp keep cutting out. I am wired and have tried moving the Sonosnet channel from 1 to 11 and vice versa with no resolution. If I switch to WiFi only, it gets even worse. Not sure if interference or another issue?  Here’s my diagnostic code 2121982684

Tengo Port y lo he conectado a un giradiscos. Mi pregunta es si puedo también conectar un reproductor de CD al mismo Port y cual sería los cables de conexión. Gracias

I have 2 Sonos Ports and they were linked to an account. I made factory reset to both of them and created a new account but there is a problem linking them or registering them to my new account

I have a long ranch house, with my router near one end. I want to optimize my recently purchased BOOST. Locating at home’s mid-length will likely solve spotty disconnects to paired Play:1 units.Can I simply buy/use a quality 25 ft. long ethernet cable extend to better locate the BOOST ? Or are there Limit complications of Cable or WI-FI distance between the BOOST and main router ? Thanks.

I want to connect the Port to an existing  hardwired system with multiple rooms of architectural in wall speakers that use a Russ Sound sdb 4.1 speaker selector and a Pioneer VSX-516 amp.  Can anyone offer advice on how/where to connect?

Just recently got a Port because my Connects memory was “done and gone’.Some trouble installing but now it works. Right now I’m trying to understand why I can’t connect to Sonos via app (s2). It seems like a lottery, it works every third or fourth time.Sometimes it’s saying that I still have my old connect in the system so “it get confused…”I should say that when the app is connected everything works great!—So, what is the problem, why the connection problem?/Lars

Hello,I have a CABASSE subwoofer. Can I connect it to my SONOS system?If so, how?I would also like to connect a vinyl turntable + usb (AKAI Professional)I have a BEAM, 2x ONE SL + SONOS RoamThank you for your answer

How do I know if my Mini Sub is working? The white light is on and I think I have carried out the connection but on checking whether I have connected I get the message on the App that the sub is not detected. I have Wi Fi and the Sub has power. On the app the sub has a red dot and the words 'not registered' beside it. Any advice?      

Hi Guys i have installed ceiling speakers and an amp in my ceiling space of closed in patio. we use it for airplay streaming and it works perfectly. Just wondering the best way to connect the TV in that area to those speakers as we didn’t run a HDMI from the TV have read people have purchased a Sonos soundbar and connected to a TV and then the soundbar and amp/ceiling speakers connect wirelessly.  would like to check this is correct and if so can we purchase any sound bar or is there only specific ones this will work with

I have 4 Connect: Amp units - one of the four suddenly stopped working - it shows no power lights when plugged in. Moderator Edit: Combined thread with reply of OP.

This topic is a year old and it was dismissed as being solved.  It’s not.   I’m reactivating my Port after two years of retirement for all Sono equipment I own.  That’s another story.   I factory reset it and it updated its OS.  Left channel does not work.   It’s not cables or stereo equipment.  A simple swap of L/R validates the source as the Port.   Wassup?   

I have a Sonos Amp that I'd like to have 2 speaker circuits connect to. One speaker circuit also has an analog volume control. Are there any concerns about doing this that I should be aware of?I also have another Sonos amp which I’d like to connect to two speakers circuits, each with individual analog volume controls. 

Hi, I have had a Sonos system for around 13 years, I use a Bridge and have 2 Connect Amps. The speakers are ceiling mounted and wired directly to the Amps. (The speakers are not Sonos).the system has always worked well however the Bridge has recently stopped powering up. So, I have purchased a Boost as thought this would be a suitable replacement. However I’m having issues connecting the Boost to the Amos as the Boost wants to use the Sonos S2 app and the Amps S1.should they be compatible or am I flogging a dead horse?? I don’t really want to shell out for 2 new amps as they are perfectly fine.  thanksPete 

I have a Sonos play base + 2 play 1s under one room, and then a separate set of move speakers. I have a project audio turntable that is connected to a Sonos port to stream vinyl. Recently I have been experiencing significant cutout issues with the playbase. The audio will drop for up to 10 seconds before resuming. If I am streaming to both the play base and the move speakers, the audio only cuts out on the play base, so I know it’s not the port causing the issue. But it is making listening to records impossible.  has anyone experienced this? The device is about 6 years old so I’m unsure if it’s reached end of life, but I experience zero Audio issues when watching Apple TV with it. 

I have a BR100 bridge and the power light is not coming on.I have checked power source and all good.it has a uk three pin plug on the power cable and looks like it is none repairable, I can’t change the fuse.any ideas?

Hi all,My Sonos Connect box stopped responding with no lights on the front panel.  I replaced the power supply (via eBay) and eventually managed to get it set up with SonoS S1 iPhone app, but I cannot get my other SonoS boxes to connect. The rest of my system consists of 3 x Connect:Amp and 3 x Play-3.  I’m trying to add the first Connect:Amp and have turned the power off to all the other boxes.  I would prefer to use wired connections for all the boxes as we have something interfering with the Sonos wifi signals for about 6 hours each day, and I want to avoid any potential problem with WiFi booster discs.Here are the detailed steps I’ve carried outperformed a factory reset on the Connect:Amp box (by holding down the mute and vol+ buttons when plugging in). powered down the Connect:Amp and turned it back on.  Light starts by flashing white, and then the settles on a slow flashing green mute button on my iPhone SonoS S1 app, I go to System / Add Product.  “Searching for your product” -

 "Lost sound from Connect to Denon receiver to listen to music on external B&W speakers. Through multiple contacts with Sonos, I was told my Connect was malfunctioning. Consequently, I ordered a Port to replace the Connect. I still have no sound. Anyone got a fix for me? ".

Hello,  After having done renovation works at our house, I tried to install my favorite speakers again in each room. All is going well when I connect via the laptop (which is connected via Wifi), but when I want to control SONOS via my iphone app (all updated) - it doesnt show all speakers, has problems with finding the system at all, or does not push my actions to the system. Any help?

I have a 3 Sonos connect system with an AMP and a Bridge from 2012. I have a bad Connect I believe. But not seeing any new units to purchase. Is there a replacement for the Connect?Brad 

Every time except for one Artist I get the error message when trying to play music. Unable to play xxxxxxx cannot connect to \\xxxxxxxx because the server cannot be found.My WIFI is 1GB and having no other issues. Thanks, Brad

I use Series 1 Sonos products in 4 rooms. I have a Sonos 3, I use a Sonos amp and i have two Sonos Connects interfacing with two separate amplifiers both with in built DAC’s . One of the Connect’s has stopped functioning and needs replaced. I currently use the optical connection in the Cyrus DAC 8 . My question is can I drop in the replacement Port product or will this require two different apps to work my system- one Series One and one Series 2? 

I am now connected to Sonos 2 app and all works well except my external cd multiplayer because it was through Connect:AMP but now says only works with Sonos 1 but I cannot see a replacement, any suggestions I would be grateful Moderator edit: Changed Connect to Connect:AMP and Sonos 2 to Sonos 1 for accuracy