Components & Architectural

My Sonos system features a sound bar and sub, as well as a Connect Amp that powers non Sonos speakers wired into my ceilings. I bought a Fluance turntable and pre amp and got a Connect to link it to the system (it’s in a different room than the connect amp). When I play the turntable Through the sound bar and sub it sounds great. But when it plays through the wired speakers it skips. Sonos says the turntable requires a separate amp to power the non Sonos speakers. They recommended either an Amp or a Port to replace the Connect. But I’m wondering if I should just buy a used Connect Amp instead. Much less expensive. 

Hi,  I have a Sonos Arc and Sonos Connect Amp that plays sound from my tv. The arc will continue playing audio but randomly the speakers in my ceiling connected to the amp keep cutting out. I am wired and have tried moving the Sonosnet channel from 1 to 11 and vice versa with no resolution. If I switch to WiFi only, it gets even worse. Not sure if interference or another issue?  Here’s my diagnostic code 2121982684

Tengo Port y lo he conectado a un giradiscos. Mi pregunta es si puedo también conectar un reproductor de CD al mismo Port y cual sería los cables de conexión. Gracias

I have just upgraded from a Audio Technica turntable to a Pro-Ject Automat A1 which has a line in to a pair of grouped 5’s. The new turntable, like the previous, has a built in Pre Amp, but while the previous turntable worked flawlessly as soon as the needle dropped BUT with the Pro-Ject I need to pull out the line in cord and reinsert it every time to get the music to play.My App is configured properly, Autoplay etc.Any feedback will be appreciated.Stu 

I have 2 Sonos Ports and they were linked to an account. I made factory reset to both of them and created a new account but there is a problem linking them or registering them to my new account

I have 2 era 300 speakers and have just bought a project T1 turntable.  To integrate the turntable I can see that you connect it one of the speakers.  Will the music automatically come out if both speakers when I play an album ?  Thanks 

I have a long ranch house, with my router near one end. I want to optimize my recently purchased BOOST. Locating at home’s mid-length will likely solve spotty disconnects to paired Play:1 units.Can I simply buy/use a quality 25 ft. long ethernet cable extend to better locate the BOOST ? Or are there Limit complications of Cable or WI-FI distance between the BOOST and main router ? Thanks.

I have the gen 1 connect linked to an amplifier with non sonos speakers. (Using S1 app)i would like to add a record player to the setup (vinyl player-connect-amp) is this feasible? what do i need?can I connect them to my other sonos products that are from gen 1?   thanks in advance!  

I want to connect the Port to an existing  hardwired system with multiple rooms of architectural in wall speakers that use a Russ Sound sdb 4.1 speaker selector and a Pioneer VSX-516 amp.  Can anyone offer advice on how/where to connect?

Hii can’t seem to pair via Bluetooth my gen5 to my new Sony PS LS 310 BT, it does have a preamp included I am not very good with tech but brought this as seemed easy with the reviews, but not for me i am sure I read the gen5 would work, I also have other player 1 but don’t think these would workany help really appreciated 

Just recently got a Port because my Connects memory was “done and gone’.Some trouble installing but now it works. Right now I’m trying to understand why I can’t connect to Sonos via app (s2). It seems like a lottery, it works every third or fourth time.Sometimes it’s saying that I still have my old connect in the system so “it get confused…”I should say that when the app is connected everything works great!—So, what is the problem, why the connection problem?/Lars

Hello,I have a CABASSE subwoofer. Can I connect it to my SONOS system?If so, how?I would also like to connect a vinyl turntable + usb (AKAI Professional)I have a BEAM, 2x ONE SL + SONOS RoamThank you for your answer

I have an Audio Technica turntable.  i want to connect to Sonos 2 speakers.  how do i do that and which cables/box do i need

I have a pair of Sonos Fives configured as stereo pair.  I have a turntable connected to one (eg left).  When playing from Line-In only one speaker works (it’s fine if I use another source eg streaming).  I can switch the configuration to the other speaker and the same.  In fact, without changing the configuration, with line in to RH speaker, I only get sound from LH speaker!  So there seems to be no issue with the speakers.  As a lay novice, I have picked up that this may be something to do with the network.  Any clues as to the issue and how I could resolve so I can play my Vinyl through both speakers?

How do I know if my Mini Sub is working? The white light is on and I think I have carried out the connection but on checking whether I have connected I get the message on the App that the sub is not detected. I have Wi Fi and the Sub has power. On the app the sub has a red dot and the words 'not registered' beside it. Any advice?      

Hi Guys i have installed ceiling speakers and an amp in my ceiling space of closed in patio. we use it for airplay streaming and it works perfectly. Just wondering the best way to connect the TV in that area to those speakers as we didn’t run a HDMI from the TV have read people have purchased a Sonos soundbar and connected to a TV and then the soundbar and amp/ceiling speakers connect wirelessly.  would like to check this is correct and if so can we purchase any sound bar or is there only specific ones this will work with

I have 4 Connect: Amp units - one of the four suddenly stopped working - it shows no power lights when plugged in. Moderator Edit: Combined thread with reply of OP.

This topic is a year old and it was dismissed as being solved.  It’s not.   I’m reactivating my Port after two years of retirement for all Sono equipment I own.  That’s another story.   I factory reset it and it updated its OS.  Left channel does not work.   It’s not cables or stereo equipment.  A simple swap of L/R validates the source as the Port.   Wassup?   

I have a Pro-Ject T1 Phono SB Turntable connected to a Sonos Five.When I play a record, I can hear the music from the record very faintly where the needle meets the vinyl. It’s also playing in the speaker as normal. Is this normal? Can I do anything to stop the music sounding at the surface of the vinyl as it’s a little delay so noticeable when you listen with the lower volume in the speaker.

Hi. I’m new to the Sonos family and have 4 Sonance ceiling speakers connected to an amp. An Arc and Sub. Set up as 2 groups. I’m thinking of adding a turntable and am a bit limited with wiring it to the amp. I’m thinking of a wireless turntable and been researching Victrola Onyx/Carbon. Anyone got experience of these or something similar that can wirelessly (not Bluetooth) get integrated with the Sonos set up? 

Hi I’ve a connect amp wired to a stereo speaker in a room. The audio from vocals has gone very low but the music is fine. I can hear audio if I switch the settings to extreme left or right but then sacrifice music. This worked fine until yesterday. Any ideas? Thanks. I’m 

Not sure when it started exactly but I get this chirping/squeaking sound on all my Sonos speakers (Combination of S1’s and one S5 and a playpar.).    I’m on S1 and do not intend to upgrade in case that should be the solution to this problem.   Submitted Diagnostic Information here:  Confirmation number is: 1740163293.

I have just purchased a Sonos Project Turntable and I’m trying to connect it to my Era 300. I have used the cables provided and the RCA adapter provided. I had an RCA to USB in the house but it is generic and not from Sonos. When plugged in the turntable seems to be working but the Sonos app does not see anything under Line In. please can you help

I've currently purchased 2x Era 100's to connect a to my Beam Gen 2 as a TV surround setup and general music playback to the living room.I also have a turntable (with pre amp) which I was hoping to connect via line-in on one Era 100 to play put through the surround setup. I learned that doesn't work (currently). Is there any solution to having the turntable play on the surround setup? Would the Port solve this? Any other recommendations?

I have a Sonos Amp that I'd like to have 2 speaker circuits connect to. One speaker circuit also has an analog volume control. Are there any concerns about doing this that I should be aware of?I also have another Sonos amp which I’d like to connect to two speakers circuits, each with individual analog volume controls.