Skip to main content
Avid Contributor I
Dec 15, 2022 7:01 PM UTC
Answered

access point mode on router not working on sonos one.

I have been battling this issue now for almost a year. I have 2 routers. The primary router is where the internet comes into my house. From there, I have an Ethernet cable that runs approximately 125 feet into my garage and connects to another router (R6900v2). I have problems with my Sonos speakers dropping connection in my garage. In my opinion they are trying to grab the signal from the primary router in the house. I have contacted Sonos, my ISP, and Netgear. No one seems to help. Sonos says put the garage router in Bridge mode. I have tried, but am not tech savvy enough to trouble shoot. When I’m bridge mode, I can not access internet. The last time I asked the Netgear community, I was told to run in access point mode. I have asked a few different techs at NETGEAR.  They confirm to put router in access point.  This does not work either. My speakers play for about 20-30 minutes and then drop. My ISP is no help at all. Can someone please help?!?!?  

This topic has been closed for further comments. You can use the search bar to find a similar topic, or create a new one by clicking Create Topic at the top of the page.
Ken_Griffiths
Dec 20, 2022 8:35 PM UTC

I did everything you suggested.  Music plays in garage from anywhere from 10 minutes to two hours, then stops.  Speaker then flashes a slow, bright white flash.

 

I ran another diagnostic.  Here is the number. 460693807

Do you perhaps have QoS, or ‘Airtime fairness’ enabled on your router? If so, try disabling those features. If not done already, set the 2.4 GHz band to use either channel 1, 6 or 11 and set a channel-width of 20Mhz only. The settings should be the same for both AP’s as they are presumably using the same subnet.

30 replies

Corry P
Sonos Staff
Dec 16, 2022 9:39 AM UTC

Hi @jellikit 

Thanks for your post!

Sorry to hear you’ve been fighting this for so long! I’ll see what I can do to help.

First of all, Bridge mode and Access Point mode are roughly the same thing - Bridge mode (or wireless bridge mode, as Netgear call it) will use WiFi as the backhaul to your internet connection, Access Point mode will use the ethernet cable instead. It is very important that one of these modes is used - if not, you are creating a separate network, isolated from the first. One thing you will need to make sure of is that the ethernet cable going to the second router should be plugged into it’s Internet/WAN port, not one of the standard ports.

Your system is using SonosNet - this means that if the Garage speaker can pick SonosNet up, it will prefer it over any WiFi connection. It sounds like this isn’t likely due to the distance and the Garage speaker will need to connect to WiFi.

It looks like at least part of the problem was that the Garage speaker was not set up as part of your existing system, but was in fact forming a new system of it’s own. You’ve already fixed that, which is good.

You say the speakers play for 20-30 min? Please submit a support diagnostic while they are playing and report the given number here. I’m not sure if “and then drop” just means they stop playing or if they disappear from the app, but please submit another diagnostic at this point too. Thanks.

 

 

Translate
"Common sense is the collection of prejudices acquired by age eighteen." - Albert Einstein
jellikitAuthor
Avid Contributor I
Dec 16, 2022 4:00 PM UTC

Corey-

 

Thank you for taking the time to help.  
 

yes, the Ethernet cable is connected to the WAN port on the secondary router.  
 

the garage speaker is running Wi-Fi from the garage router.  But, there is a weak signal coming from the primary router in the house.  Can this be the issue?  
 

I spent 2 hours on the phone with Sonos.  I believe they set up the garage speaker separately.  But, when I open the primary router settings, the MAC address for the garage speaker is listed in those settings.  Not sure if this is because of the access point mode of the garage router or not?

when the garage speaker “drops out”, it quits working.  Then the light flashes white.  But it is a brighter, stronger flash as compared to when you reboot the speaker.

I submitted diagnostics.  Here is the number 1523545283

 

do I need to provide any information?

 

your help is greatly appreciated!

 

thank you


 

Translate
Ken_Griffiths
Dec 16, 2022 4:08 PM UTC

Corey-

 

Thank you for taking the time to help.  
 

yes, the Ethernet cable is connected to the WAN port on the secondary router.  
 

the garage speaker is running Wi-Fi from the garage router.  But, there is a weak signal coming from the primary router in the house.  Can this be the issue?  
 

I spent 2 hours on the phone with Sonos.  I believe they set up the garage speaker separately.  But, when I open the primary router settings, the MAC address for the garage speaker is listed in those settings.  Not sure if this is because of the access point mode of the garage router or not?

when the garage speaker “drops out”, it quits working.  Then the light flashes white.  But it is a brighter, stronger flash as compared to when you reboot the speaker.

I submitted diagnostics.  Here is the number 1523545283

 

do I need to provide any information?

 

your help is greatly appreciated!

 

thank you

 

Can’t you simply use the routers MAC address filtering feature to get your products onto the required access point, so that all in the garage are using the nearby router etc.

I would just ensure too that both routers are broadcasting the same subnet with identical WiFi SSID/credentials, channels and channel-width (20Mhz only is recommended for the 2.4Ghz band).

Translate
Ken_Griffiths
Dec 16, 2022 4:16 PM UTC

By the way I can’t personally see how both routers can be on the same local subnet if using the WAN port unless the router specifically has a ‘bridge mode’ setting that turns that into a LAN port for ‘switching’ purposes, but definitely keep both devices (AP’s) so that they use the same LAN subnet, rather than using double NAT.

Translate
jellikitAuthor
Avid Contributor I
Dec 16, 2022 4:33 PM UTC

This is where it goes over my head…….

do you recommend I call Sonos and pass this along to them so they can walk me through? I have literally talked to 5 -6 

different techs and none of them have suggested this.  I do appreciate your help, but do not know how to set this up…….

Translate
Corry P
Sonos Staff
Dec 16, 2022 4:38 PM UTC

Hi @jellikit 

Thanks for the diagnostic. Your Garage speaker is connecting to SonosNet via the Kitchen speaker, and therefore ignoring available WiFi alternatives. As far as the speaker is concerned, the settings of the second router (and the fact that it exists at all) is irrelevant. The Sonos app may see things differently when you are in that area, however - to it, the second router may well be important. If the Sonos app can connect to your Sonos system while your phone is on the second router’s WiFi, all is working well.

As for the Garage speaker, I can only really recommend trying to shorten an imagined straight line between the Garage and Kitchen speakers. If you can try to also shorten the amount of that line that is going through a wall, that would also help (a signal going at right-angles to a wall has less matter to penetrate than one approaching at a shallow angle).

I would also recommend checking the Kitchen speaker’s location for any sources of interference or signal blocking (thick materials, especially metal).

Moreover, your Sonos system does not know any WiFi passwords, so even if the Garage speaker could not connect to SonosNet, it wouldn’t know how to connect to either router. An option you have, therefore, is to give the Sonos system the credentials to get on to your WiFi (both, if the routers have different credentials - the first router first, then the second. I recommend having the same credentials for each), then disconnect the ethernet cable going to the Playbar. This will put all your Sonos devices on WiFi, and the Garage speaker should connect to the second router’s WiFi with a better signal strength that is currently found on SonosNet.

  1. Open the Sonos S2 app for iOS or Android.
  2. From the Settings tab, press System > Network > Manage Networks.
  3. Press Update Networks and follow the prompts to connect Sonos to your Wi-Fi network.
  4. Once the wireless setup is complete, disconnect the Ethernet cable from any Sonos products wired to your router.

I hope this helps.

Translate
"Common sense is the collection of prejudices acquired by age eighteen." - Albert Einstein
jellikitAuthor
Avid Contributor I
Dec 16, 2022 5:14 PM UTC

I appreciate all of the information.

so…….just to make sure I fully understand:

 

I can not move my kitchen speaker any closer to the garage, nor can I move either speaker to improve the angle of transmission.  So, I need to get the garage speaker to connect to the second router, which is in the garage, correct?

In order to do this, I need to give both routers the same credentials.  Does this mean the same SSID and password for the garage router?  What other credentials do I need to duplicate?

 

Then, disconnect Ethernet cable from the play bar, and finally follow the directions you gave for updating the network?

 

Lastly, if both routers have the same credentials, and garage is an access point, after updating the network the Sonos app should work seamlessly for the house and garage systems?

Translate
Corry P
Sonos Staff
Dec 19, 2022 9:40 AM UTC

Hi @jellikit 

So, I need to get the garage speaker to connect to the second router, which is in the garage, correct?

Yes - from your response, it sounds like it.

 

In order to do this, I need to give both routers the same credentials.  Does this mean the same SSID and password for the garage router?  What other credentials do I need to duplicate?

These are what I refer to as credentials - hopefully, you won’t need to adjust other settings. So, yes - keep the SSID and password the same across the two routers.

Then, disconnect Ethernet cable from the play bar, and finally follow the directions you gave for updating the network?

You’ll want to keep the ethernet cable connected until the Sonos system has been told the WiFi credentials - the app will in fact tell you when to remove the ethernet cable. Please follow the instructions at Connect Sonos to a new router or Wi-Fi network.

Lastly, if both routers have the same credentials, and garage is an access point, after updating the network the Sonos app should work seamlessly for the house and garage systems?

Yes, though they are not, nor will they be, separate systems. Expect to see all your speakers in the app at one time as you do now (when Garage isn’t misbehaving), regardless of which router your phone is connected to.

I hope this helps.

 

 

Translate
"Common sense is the collection of prejudices acquired by age eighteen." - Albert Einstein
jellikitAuthor
Avid Contributor I
Dec 19, 2022 4:47 PM UTC

I will try it for a day or two and let you know.  Thanks again!

Translate
jellikitAuthor
Avid Contributor I
Dec 20, 2022 7:40 PM UTC

I did everything you suggested.  Music plays in garage from anywhere from 10 minutes to two hours, then stops.  Speaker then flashes a slow, bright white flash.

 

I ran another diagnostic.  Here is the number. 460693807

Translate