Skip to main content
Contributor I
May 15, 2014 12:23 PM UTC

unplugging temporarily to move a speaker

If i need to temporarily unplug a sonos component that is already configured and working, is there a re-start up procedure, or will it reboot itself when it is plugged back in?
    This topic has been closed for further comments. You can use the search bar to find a similar topic, or create a new one by clicking Create Topic at the top of the page.

    15 replies

    Oct 2, 2016 4:32 AM UTC
    I think you're being presumptuous, if I'm sitting outside 99% of the time I don't need or want the music to be playing in the house. What would be the point? I'm not in the house, so I don't want Sonos assuming that I still want the music to play inside.
    Translate
    Lyricist II
    Oct 2, 2016 1:04 PM UTC
    I think you're being presumptuous, if I'm sitting outside 99% of the time I don't need or want the music to be playing in the house. What would be the point? I'm not in the house, so I don't want Sonos assuming that I still want the music to play inside.

    If you go outside and don't want music playing in the house you can stop it playing.

    The other day I pulled out the table that my conservatory speaker is on to clean the window behind it. The power lead moved slightly in the speaker - a not uncommon thing to happen as the connectors seem a bit flaky - and the power went off to it. That speaker is the master of a five speaker group so they were all ungrouped. Maybe not a big deal but I don't think Sonos should presume anything. If a speaker gets powered down and then back up it should revert to its previous state including retaining the grouping and queue and continuing playing whatever was playing. If you want to move a speaker and reconfigure it then you can use the controller to do it but I bet power outages way exceed the number of times you want to move a speaker.

    Another thing that happened recently was that for some reason the conservatory speaker got lost to the system so the rest of the group weren't playing. In the controller the speaker wasn't there at all although it was still playing music. To resolve it I had to re-add the speaker then regroup everything. Strange!
    Translate
    ratty
    Oct 2, 2016 1:17 PM UTC
    That speaker is the master of a five speaker group so they were all ungrouped.
    In that case you have network issues. When the group coordinator ('master' in your terminology) is dropped, another player should take over.

    If a speaker gets powered down and then back up it should revert to its previous state including retaining the grouping and queue and continuing playing whatever was playing.

    While there have been requests for persistent groups (and a stereo pair is in some ways a persistent group), storing the queue in non-volatile memory throws up various issues. Firstly in some models the non-volatile storage is maxed out, which is why the library index is constrained in size. Accommodating a potentially large queue would be out of the question. But also storing a queue in non-volatile storage would risk wearing it out. Persistent memory offers a finite number of write cycles. It's large, and such memory uses wear-levelling techniques, but a canny system designer would not want to store short-lived data there.

    Another thing that happened recently was that for some reason the conservatory speaker got lost to the system so the rest of the group weren't playing. In the controller the speaker wasn't there at all although it was still playing music.

    This supports the hypothesis that you have network issues, particularly around that player. (See above,)
    Translate
    Lyricist II
    Oct 2, 2016 2:36 PM UTC
    In that case you have network issues. When the group coordinator ('master' in your terminology) is dropped, another player should take over.
    Thanks, ratty. I'll look into the network thing. I have a boost that is only three feet away from the network hub and the conservatory speaker is only about ten feet as the crow flies from the boost.
    I take your point about the amount of memory for temporary data, however I still feel that when a speaker powers down then up it should still return to its group.
    Translate
    ratty
    Oct 2, 2016 2:40 PM UTC
    If you can't figure things out then submit a system diagnostic and post the number. Sonos Support can take a look at the state of your SonosNet.

    On the grouping question, I have some sympathy with those requesting persistent groups and/or group presets. It's clearly not been a high priority for Sonos.
    Translate