Skip to main content
Enthusiast I
Dec 14, 2019 6:28 PM UTC
Question

Sonos Move power cord?

Just taken delivery of a Move and am disappointed to find that the charger socket, charger base and cable are all hard wired together.  I want to position the Move on some built-in desk furniture, where all the power sockets are located underneath, accessible through cutouts in the desk top.  Problem is neither the charger socket nor the base will fit through the cutout, so I am going to have to run the cable across the desk.  I realise I could probably use the USB-C charging point instead but then I’d lose the convenience of just being to pick up the Move and go when I want to take the music outside.

Normal way round this sort of problem would be to cut off the moulded power plug and fit another one back after running the cable through the cutout, but the plug on the Move is integral with the charger.  Since the charger base only has a two pin spring-loaded connection point to connect to the Move battery, my assumption is that the cable is ordinary twin core low voltage cable.  Is there any reason why I shouldn’t cut the cable and rejoin using ordinary cable jointing block, once cable has been passed through the desk cutout?

Seems like a simple solution, but don’t want to risk screwing up a fairly expensive new purchase.  Anyone got any reasons why it wouldn’t be ok? 

    This topic has been closed for further comments. You can use the search bar to find a similar topic, or create a new one by clicking Create Topic at the top of the page.

    19 replies

    bjw10Author
    Enthusiast I
    Mar 27, 2020 11:25 AM UTC

    @gb13 you asked to be kept informed about what I did re the cable issue.  Well, I finally got round to making a decision and having considered all the other possible locations, it seemed that the only viable option was to cut and re-join the cable after passing it through the desk cutout.

    Initially I cut through just the outer protection and was a bit surprised to see what looked a fine braided metal sheath inside.  This didn't worry me unduly, since there appeared to be 2 further cables within.  However, when I finally cut through the entire cable, it transpired that there was only a single cable inside.  It was coloured black and white so had given the appearance of two separate cables.

    Anyway, I just used a standard cable jointing block to join both the braided sheath, which I assume to be an earth as well as protection for the cable, and the black/white cable.  Now all works well with the Move positioned exactly where I want it and no visible cables trailing across the desk. Job done! 

    Translate
    Lyricist II
    Mar 27, 2020 3:16 PM UTC

    @bjw10 Amazing to hear- thank you so much for the update. I would love to do this as well.

    Do you mind linking to the block you used (or something similar)? I’ve never messed around with something like this before, so imagine I will be watching many YouTube videos and trying not to ruin the cable.

    Translate
    bryan654321
    Trending Lyricist I
    Mar 27, 2020 3:53 PM UTC

    This article might help you

    https://support.sonos.com/s/article/3640?language=en_US

    Translate
    Bryan Anderson
    Lyricist I
    Apr 8, 2020 2:27 PM UTC

    Dear Sonos-Team,

    PLEASE change this unacceptable design - it is not really handy not being able to unplug the cable of the charger or the socket to put the cable through smaller holes in tables or other furniture!!!

    If somebody has the same Problem as @bjw10 and don’t want to cut the power cord, I managed to open the charger base. I pulled up the rubber and the clear plastic then there were 4 screws, two holding the plastic and two fixing the metal contacts. The two wires were soldered to the contacts, so if you need more than this space you have to unsolder those - but for me it was now slim enough! I made me a picture of the contacts and also wrote down on which side there must be mounted again - for safety reasons!

     After putting everything together again, it works like a charm and it fits well on the console!

    Translate
    bjw10Author
    Enthusiast I
    Apr 8, 2020 3:32 PM UTC

    Hi mborko,

    Thanks for adding your comments to this topic.  I did look to see if there was any way into either the charger or the base, but clearly didn’t have you confidence to pull it apart.  Well done, I think your solution is more elegant, but as you say, we shouldn’t have to do this, especially given almost every other bit of Sonos kit I can think of has a separate power cable!

     

     

    Translate
    Lyricist I
    May 8, 2020 6:18 PM UTC

    Thank you for posting this. I love my brand new Move. But yes the cradle cord is super inconvenient. I was hoping to thread the power supply through a grommet in my built in bookcase, but I will have to be brave and attempt one of the methods you both have suggested. I also think the volume up and down indicators are not very intuitive for everyone, and the set up prompt to press the button making the chime was weird. The top of my speaker was chiming and lighting up...thankfully I knew to press the link button from other setups. Maybe they didn’t get enough feedback when they were testing this speaker: inconvenient power supply, strange setup prompts, top buttons aren’t differentiated one from another… but it sure does have great sound where I want it!

    Translate
    Lyricist II
    May 9, 2020 5:58 PM UTC

    Add me to the list of frustrated customers with the big, bulky and hard connected power cord.  Love the move, hate the power cord.  

    Translate
    Lyricist I
    Jun 3, 2020 7:55 AM UTC

    Add me to the that same list.  It’s amazing that it is so inflexible when it costs £400.  Avoiding ugly black wires seems the point of Sonos.  I also “Love the move, hate the power cord.”

    Translate
    bockersjv
    Local Superstar
    Jun 3, 2020 9:54 AM UTC

    deleted as i did not read the OP properly!

    Translate