Skip to main content
Trending Lyricist I
Oct 26, 2019 8:27 AM UTC

Players drop out on Virgin Media network

I have 5 Sonos players on my Virgin Media home network. Most of the time everything works well but occasionally I find one or more of the players have dropped out and disappeared from the Sonos apps.

When I look at my router (Hub 2ac) device connection list it shows all the players but the ones that have dropped out are listed as connected by Ethernet whereas they are all actually on wi-fi.

The correct MAC address and IP addresses are listed with the only clue to a problem being they are listed as Ethernet connected.

Power down and up again on each player simply shifts them from Ethernet to wi-fi and then all is well again until the next time.

I don’t think it has anything to do with IP lease time as that is set at one day but the problem might only occur every two to three weeks.

Is it the hub? does anyone know?  

    This topic has been closed for further comments. You can use the search bar to find a similar topic, or create a new one by clicking Create Topic at the top of the page.

    16 replies

    ratty
    Oct 27, 2019 11:39 AM UTC

    https://en.wikipedia.org/wiki/Dnsmasq

    I use one too, embedded in third party firmware on an old Linksys box, as DHCP/DNS server. Much more configurable, with up to 100 reserved IPs and the ability to map two MACs to one IP if required (e.g. if a device has multiple NICs).

    Translate
    Ken_Griffiths
    Oct 27, 2019 11:48 AM UTC

    So if I were to get and flash an old Linksys router with say DD-WRT, do you know if dnsmasq is ‘likely' embedded in that firmware?

    Translate
    Ken_Griffiths
    Oct 27, 2019 12:10 PM UTC

    Ah I found the answer I needed here... https://wiki.dd-wrt.com/wiki/index.php/DNSMasq_as_DHCP_server 

    And sorry for taking this thread slightly off topic.

    Translate
    Trending Lyricist I
    Oct 27, 2019 3:22 PM UTC

    Continued thanks guys!  Several points here so I’ll answer in a list.

    1. I did say that it was  ‘(…. a definite and without a doubt!)’ that I did not have the problem before adding a remote access but a lifetime in engineering (not this field!) has taught me to suspect everything including my own statements! So, I think the best plan is to disable the remote wireless function on the TP-Link as I’m not currently using it for wi-fi. Obviously the frequency of this problem means that it could take some time to be certain.
    2. Just to answer the questions,  the remote TP-Link was connected by cable LAN to LAN and DHCP was disabled. It is on same SSID but different channel. (Thought it had to be!)
    3. Last week I did reserve DHCP channels for all the players on the SH2 successfully but as it happens the fault in question appeared the next day.
    4. I can’t realistically connect a player by cable. The locations are just too difficult. A question on that: I used to have a bridge before it failed. Would fitting one (a bridge) convert the system to SonosNET?
    5. OK, I’ve switched OFF the remote router wi-fi.  Lets see what happens?  I think that course may well explain a lot?
    Translate
    pwt
    Virtuoso
    Oct 27, 2019 3:29 PM UTC

    Re: 2: It’s fine for separate access points to be on the same SSID and channel. That’s how I run three separate APs in my house.

    Re: 4: The modern equivalent of a Bridge is a Boost. One of these, wired to your router, would establish SonosNet for your speakers. You could buy one on a 100-day return basis from Sonos, and see how it goes (which is what I did). However, perhaps wait to see if the problem is now resolved rather than spending money unnecessarily.

    Let us know how it goes :)

    Translate
    4 x P:5 | Sub | 4 x P:1 | 3 x Connect | 2 x Boost | Connect:Amp | 2 x One | Amp | Move | Port | Era 300
    Trending Lyricist I
    Nov 19, 2019 9:49 AM UTC

    Hello again guys.

    I’m reporting back with problem sorted!  

    After a long period with the remote access point wireless switched OFF, the fault did not occur again.

    I am therefore concluding that the players were indeed connecting to the remote wireless and therefore showing up as Ethernet connected when they disappeared from the Sonos setup.

    I decided to buy a Boost (on Ebay- good price!) and installed it in minutes.

    Job done!  Thanks for the help!!

    Translate