Skip to main content
Trending Lyricist I
Oct 26, 2019 8:27 AM UTC

Players drop out on Virgin Media network

I have 5 Sonos players on my Virgin Media home network. Most of the time everything works well but occasionally I find one or more of the players have dropped out and disappeared from the Sonos apps.

When I look at my router (Hub 2ac) device connection list it shows all the players but the ones that have dropped out are listed as connected by Ethernet whereas they are all actually on wi-fi.

The correct MAC address and IP addresses are listed with the only clue to a problem being they are listed as Ethernet connected.

Power down and up again on each player simply shifts them from Ethernet to wi-fi and then all is well again until the next time.

I don’t think it has anything to do with IP lease time as that is set at one day but the problem might only occur every two to three weeks.

Is it the hub? does anyone know?  

    This topic has been closed for further comments. You can use the search bar to find a similar topic, or create a new one by clicking Create Topic at the top of the page.

    16 replies

    pwt
    Virtuoso
    Oct 26, 2019 11:21 AM UTC

    If you have one or more Sonos devices connected by Ethernet cable, then you are running in ‘Wired’ mode, and the wireless Sonos players will be on a ‘SonosNet’ network created by the wired ones. Hence, they’ll show as Ethernet connected by the router.

    What model of VM Superhub do you have (SH2 or SH3), and how many of its wired ports have Sonos devices attached (either directly or indirectly)? Also, could you post the details of ‘About My Sonos System’ here, to confirm how the devices are connected.

    Translate
    4 x P:5 | Sub | 4 x P:1 | 3 x Connect | 2 x Boost | Connect:Amp | 2 x One | Amp | Move | Port | Era 300
    Trending Lyricist I
    Oct 26, 2019 3:18 PM UTC

    Hi. Thanks for your help.

    I have a Super Hub 2ac

    I have 2 x Playbars, 2 x Play 5 and 1 x One (5 total)

    None of the players are wired.

    (When the system is working fully, all players are shown as wireless.)

    I can’t see where to enter details in ‘About My Sonos System’ - where is it?

    Translate
    pwt
    Virtuoso
    Oct 26, 2019 8:58 PM UTC

    On a mobile controller: Settings > System > About My System
    On a desktop (macOS) controller: Sonos > About My Sonos System. Windows app should be something similar.

    Do you have any wireless access points or extenders in addition to the SH2 itself?

    Translate
    4 x P:5 | Sub | 4 x P:1 | 3 x Connect | 2 x Boost | Connect:Amp | 2 x One | Amp | Move | Port | Era 300
    Trending Lyricist I
    Oct 27, 2019 9:24 AM UTC

    Thanks again. Here is a copy of ‘About My Sonos System’:

    Associated ZP: 192.168.0.27
    ---------------------------------
    Sonos One: Bathroom
    Serial Number: 78-28-CA-B3-52-D6:E
    Version: 10.4.2 (build 521370021)
    Hardware Version: 1.21.1.8-2
    Series ID: A100
    IP Address: 192.168.0.23
    WM: 1
    ---------------------------------
    Play:5: Dining Room
    Serial Number: 00-0E-58-5A-D9-58:7
    Version: 10.4 (build 521369030)
    Hardware Version: 1.16.4.1-2
    Series ID: P100
    IP Address: 192.168.0.24
    WM: 1
    OTP: 1.1.1(1-16-4-zp5s-0.5)
    ---------------------------------
    Playbar: Lounge
    Serial Number: 00-0E-58-B6-BD-F7:9
    Version: 10.4 (build 521369030)
    Hardware Version: 1.9.1.10-2
    Series ID: A100
    IP Address: 192.168.0.25
    Audio In: No Signal
    WM: 1
    OTP: 
    ---------------------------------
    Playbar: Master Bedroom
    Serial Number: B8-E9-37-7C-FD-E8:1
    Version: 10.4 (build 521369030)
    Hardware Version: 1.9.1.10-2
    Series ID: A100
    IP Address: 192.168.0.27
    Audio In: 
    WM: 1
    OTP: 
    ---------------------------------
    Play:5: Office
    Serial Number: 00-0E-58-80-30-80:1
    Version: 10.4 (build 521369030)
    Hardware Version: 1.16.4.1-2
    Series ID: P100
    IP Address: 192.168.0.22
    WM: 1
    OTP: 1.1.1(1-16-4-zp5s-0.5)

    ---------------------------------

    I recently installed a spare router at the other end of the house as an access point BUT the problem was there before and hasn’t changed. (That’s a definite and without a doubt!)

    Translate
    pwt
    Virtuoso
    Oct 27, 2019 10:05 AM UTC

    Thanks. Currently, your speakers are all showing as WM:1, meaning that they’re connected to your WiFi (so called ‘Wireless Mode’), although it doesn’t tell you anything about which access point they’re connecting to.

    When the SH2 router indicates that speakers are connected via a wired Ethernet port instead of WiFi, it means that their connectivity to the router is indirect, i.e., they are connecting to a separate WiFi access point that is connected to your SH2 router via one of its wired connections. That’s why I asked about additional access points. If your speakers show in the SH2 as connected over a wired port, it suggests they’re switching over to connecting to the secondary router.

    Notwithstanding your comment that the problem was present before its inclusion, how is the secondary router configured, and how is it connected to the primary router?

    To operate properly, all Sonos speakers need to be on the same subnet (192.168.0.XXX in your case), and mDNS broadcast traffic needs to be unrestricted. Also make sure that there is no secondary DHCP server running.

    Translate
    4 x P:5 | Sub | 4 x P:1 | 3 x Connect | 2 x Boost | Connect:Amp | 2 x One | Amp | Move | Port | Era 300
    Ken_Griffiths
    Oct 27, 2019 10:53 AM UTC

    Paul,

    I actually know this particular VM router quite well, my suggestion would be to wire one Sonos device to it. This will switch your Sonos system over to SonosNet, 

    Make sure the SonosNet channel is set at least 5 channels away from the routers 2.4ghz channel.

    Importantly - add all your Sonos IP addresses to the routers DHCP Reservation Table… this router has issues with IP leasing and this step will stop those issues. You will find videos on YouTube of how to do this, if you are not sure how to go about it.

     

    Next, Goto the Sonos App “Settings/System/Network/Wireless Setup” and reset/remove the WiFi credentials from the App. You will not need these whilst having one device wired to the router and running in SonosNet mode.

    With regards to the other secondary router/access point, ensure you not only need to disable the DHCP server, but I would also recommend you run it’s WiFi either as follows …

    Either …

    1. With the exact same SSID, password and the same WiFi Channels as the main router for both the 2.4ghz and 5ghz bands (recommended) ....OR...
    2. With a totally different SSID and also different WiFi channels, that are at least 5 channels away from both your main routers WiFi and your SonosNeg channel… if you decide on this second option however you must ensure your Sonos mobile controller devices do not connect to this Wifi network as they will lose sight of your Sonos system.

    Hope that assists.

    Translate
    pwt
    Virtuoso
    Oct 27, 2019 11:09 AM UTC

    FWIW, I also know this router very well. I’ve had no real issues with DHCP, but Ken’s advice on reserving IP addresses does no harm, although it’s a clunky process on the SH2.

    The advice on using the same SSID & channel on the secondary router is also good, although it’s irrelevant to Sonos whether you do this on the 5GHz band.

    Personally, I’d want to root cause the issues on WiFi before giving up and switching to SonosNet, but it’s definitely worth trying if it’s convenient for you to wire one or more of your Sonos devices.

    Translate
    4 x P:5 | Sub | 4 x P:1 | 3 x Connect | 2 x Boost | Connect:Amp | 2 x One | Amp | Move | Port | Era 300
    Ken_Griffiths
    Oct 27, 2019 11:16 AM UTC

    Yes the DHCP Reservation is clunky, to say the least. It’s best to make a note of the MAC/IP addresses and switch off the devices and then add them to the table after their leasing has dropped.

    The SH2 DHCP Reservation Table is also limited to 16 devices only due to its memory capabilities  … perhaps not too important for most people, but not ideal for folk with larger Sonos systems.

    Translate
    pwt
    Virtuoso
    Oct 27, 2019 11:24 AM UTC

    Yes the DHCP Reservation is clunky, to say the least. It’s best to make a note of the MAC/IP addresses and switch off the devices and then add them to the table after their leasing has dropped.

    The SH2 DHCP Reservation Table is also limited to 16 devices only due to its memory capabilities  … perhaps not too important for most people, but not ideal for folk with larger Sonos systems.

    Yep. I run a separate DHCP server (dnsmasq) that is much more powerful and easy to configure, but I do so for reasons mostly unrelated to Sonos. I never had any substantial issues with the SH2’s IP management as far as Sonos was concerned.

    Translate
    4 x P:5 | Sub | 4 x P:1 | 3 x Connect | 2 x Boost | Connect:Amp | 2 x One | Amp | Move | Port | Era 300
    Ken_Griffiths
    Oct 27, 2019 11:32 AM UTC

    pwt, 

    I did, my SH2 often got confused during Sonos updates. Always failed at the 'cleanup' stage and I had to restart the router to get the devices back online, but reserving the IP addresses sorted it for me. That was often my experience, at least.

    I’ve not heard/tried dnsmaq. Would appreciate more info about that please, or maybe a pointer.. thanks.:thumbsup:

    Translate