Sonos Amp disappears

Does rebooting AMP bring it back online?

Following. I’ve got similar issues occasionally with Unify Dream Router and Sonos AMP. All other Sonos equipment including AMP is connected wireless. Recently I had to reboot (pull the plug) on the AMP to get it responsive again (still played music but did not respond to changes to songs or volume). 

Since the hard reboot it has worked ok again for a few days, but clearly disturbing and annoying.

Something important to keep in mind is that most Sonos will connect to SonosNet, not your WiFi when any Sonos device is wired to your Ethernet. Note that it is important to not wire only a Sub or Surround to Ethernet as that often leads to frustrations.

There is a good Ubiquity Settings topic here in the forums.

Good morning, thanks for your help!

Yes, it does. What does that fact indicate to you?

The issue also occurs when all my Sonos devices are connected wirelessly. That is why I am unsure if the issue is even related to Unifi, I read the Sonos/Unifi issues happen mostly when mixing wired and wirelessly.

When I had the initial setup issues I tried a lot of the recommendations, but none helped. The only thing that helped back then was switching the AMP from wired to wireless. Only then I switched the AMP back to wired to try if it helps.

But anyway, I‘ll try some of those recommended settings again. 

We can’t rule out a hardware fault with AMP. Have you reserved IP addresses? Are the PING times to AMP and other clients relatively constant?

If more than one SONOS unit is wired to the switch, make sure it is set to STP not RSTP (the default). Also I don’t recommend wiring any SONOS units to the UDM PRO. I once had a couple PLAY:3’s wired through a UDM PRO. Immediately after a network reset I was getting 900+Mbps. About 20min later I was getting about 19Kbps and PING times were terrible, if the packets were not dropped. Classic storm,

Thanks! I do have a network outlet next to one of the SONOS ONEs, and I’d like to try to run it wired. Regarding the UDM PRO, it is only connected to the switch and all clients are connected to the switch, so that is not an issue.

So far it is still looking good with my setup, the AMP survived the night. :-)

Btw, because you mention 900 Mbps, it seems the AMP only has 100 Mbit interfaces?

All SONOS units are 10/100. Back in 2005 you could use SONOS units as wireless mesh points and switches by wiring to or between SONOS and other products. At that time there were no other consumer products that could mesh. Under very favorable conditions speeds in the 10-20Mbps range could be achieved. This was great when our Internet connections were in the 2 Mbps (or less) class and we had a couple computers and a printer on the network. At this point, speeds in this class are lame and there are many very capable mesh systems on the consumer market. I’m not convinced that the current consumer mesh systems are quite as painless to setup and maintain as the original SonosNet mesh, but a modern mesh system is considered “broken” if it runs at 10 Mbps. Each new generation noticeably improves.

In your case I think that you’ll find that WiFi6 will significantly improve wireless connectivity. 

Personally, I’m waiting to give WiFi7 more time to “bake” before I update. I’m partially WiFi6 in my home. In spite of all the hype, the WiFi7 standard was formally adopted earlier this year and we are just beginning to see a flood of WiFi6 products entering the market. WiFi7 products are still in the pre first generation, early adoption stage.

Hi,

How does the SONOS devices decide whether to use WiFi or SonosNet, now that I have my AMP wired?

Regarding WiFi version, in my Unifi network application the 5 GHz band is shown as WiFi 6, but the 2.4 GHz band only at WiFi 4, for whatever reason. The two SONOS ONEs are shown as connected to the 2.4 GHz band. 
 

Ubiquiti must use use the standard supported by the client. WiFi6 access points are backwards compatible with older units that cannot make sense out of WiFi6 advanced details. Full WiFi6 support requires a client hardware upgrade. WiFi6 reaches its full potential when all clients support WiFi6. Regardless, I find that WiFi6 access points are more capable than older assess points. Networks that are struggling, will often improve considerably if the access points are upgraded to WiFi6.

In my opinion, if current performance is satisfactory, I think that waiting for WiFi7 to mature will be the most cost effective approach. This will require a few years. But don’t hesitate to install WiFi6 access points if you need a performance boost.

Thanks - for now we are happy with our wireless performance anyway. But I will look into why our 2.4 GHz seems to be setup as WiFi4 in general. The info on the screenshot seems to apply to the access point in general, not individual devices. Or do all devices need to support WiFi6 for the access point to be able to use the newer version?

I’d send you a picture of my client list but the Ubiquity MFA access system is hosed and nobody using it can access their own equipment, support or even the web forum to complain.

I’m pretty sure I have multiple types of clients listed there but I can’t see them tonight.