Components & Architectural

Since 2014, you have gone from bad to worse. While your sound remains great (who’s isn’t?), your lackluster software upgrades / support have been a perpetual joke. How are you still competing with superior vendors, one might ask?  I’ll leave that to others to discover.

Current setup: turntable --> pre-amp --> era 100. i want to have the turntable audio also play out of my Adam A5X active studio monitors.Can i get a sonos port, and connect the outputs to the Adam A5x(no inputs connected to port) and then group the Era 100 turntable audio to the port, so that the audio from the turntable plays out of both the era 100 and the adam a5x’s via the port?if so, will there be a delay of any kind?

I have a house with in-wall/in-ceiling speakers in 4 different rooms plus outdoor for a total of 5 zones. They are connected to a mechanical switch box and then a Denon AVR. The switch can select one or more zones for playing the source audio. Each zone has a wall mounted volume control.I know I can connect these speakers to my Sonos system with Sonos Port but I’d like to see the individual zones in the Sonos App and control the volume using the app. Is there an alternative to the existing “dumb” speaker selector switch that will integrate with Sonos and let me do what I want?Any thoughts or suggestions would be much appreciated!  Thanks in advance. 

Mon ampli ne veut plus s’allumer 

 HelloI have a Sonos AMP. C17 had a short circuit. Unfortunately, this also burned out the L2 coil (470 µH). Apparently, the circuit path on the multilayer board is also broken, and I believe the path from the L2 coil to resistor R1263 is also broken. Can anyone confirm that the path goes there? R1263 (1 kΩ) has approximately 300V there.Unfortunately, my AMP isn't working yet because I don't fully understand what SONOS has put together. It contains several PWM chips.RegardsStephan

I am very happy with my Port. I do think it is priced high.The analog in works fine with my analog turntable and the digital out coax ‘stream through’ to an external dac.What I am missing is an optical in for my cd player.I think it could be a great feature for the Port and increase the value for a small cost. What do you think? My two cents.

Wondering if there will be a new Sonos amp coming? I have Sonos products but I have some passive speakers that I want to hook up into the Sonos eco system in a surround sound set up. The current amp has aging WiFi, and I see there are some rumors swirling of a new amp. If anyone can shed light on this it’ll be much appreciated 

I was forced to change my wifi password. A plain, simple password change. No changes to the network as such.To no surprise, this did not go down very well with the Sonos system. Not able to handle at all. Components dropping out, lost, half of the stereo pair and so on. The default message: “An error occured”. Go figure.The solution: hard reset of all components connected wireless, followed by several reboots of router and components. Took me about four hours to get it all working again. Well, some sort of working. Still issues with sound randomly dropping.Needless to say I didn’t bother to contact support as they would have adviced what I already new: reset and reboot.One should assume a password change should be straightforward but no, no, not with Sonos. Unbelievable, but also not surprised. After more than a year (and still counting) after the Grand App Debacle getting used to this.

My play 1 (gen 1) is dead! I opened it up to check the 2amp fuse which is fine. On examination I found that R310 has blown.  My question is what value resistor is this? Any ideas what may have caused it to pop?  

Hi Team,I am facing random connection drop issues between Sonos app on iPhone and the speaker system. Here is the situation. Everything was working as expected for the past three years but since almost a week, Sonos app on my iPhone dies with the error - No Sonos system found. Opening play.sonos.com on a computer also shows the same error. Randomly after closing the app and relaunching it for a few times, the system shows up again. But it is mostly hit and try.Have been using Sonos Arc + Siub Gen 3 + Sonos Roam for the past 3+ years without any issue. Nothing has changed in terms of SSID, router, placement of the system etc. Sonos Arc, Sonos Sub Gen 3, Sonos Roam are all connected to the router (wirelessly), and the internet is working. All systems are up and running as expected. All Sonos devices are working as expected.  The iPhone with Sonos app (and computer with play.sonos.com open) is on the same network as the Sonos devices. Airplay on iPhone shows Sonos system as an option. Ran

I have Era 100 speakers installed in my home. I also have a turntable with its built-in simple amplifier. I want to know what equipment I should purchase so the turntable can play through my Era 100 speakers, and I also want to listen to my TV through the same speakers. I understand I should buy an amplifier and a sound bar, and I could achieve what I want, but I'd like to be sure.

I currently have  a Gen2 amp running two Bose freespace 51’s for my backyard audio. I want to upgrade to the Gen3 amp and am considering replacing the Bose speakers with the Sonance Omni-6t 360 degree in ground speakers since the Bose speakers cannot handle the additional watts that the Gen3 amp pushes. Anyone running this setup? 

I have a Sonos Connect Amp and while blowing dust out of the stereo cabinet the Sonos Connect amp fried. Opening it up I see a Lion power transformer is burned. Looking to repair with a Lion 1706, with a number 6016A0005701. Is this feasible? The internet does not find this transformer that is installed on the circuit board. 

I just read on here that someone was having trouble with blown Sonance outdoor but the thread is now closed. So have to make a new oneI have a Beach Bar Restaurant & my beach area with all the tables is 20m x 20m 1 side being the sea and the opposite centre is a tree planning to mount high up 2 x Sonance outdoor facing diagonal L & R to the beach and the Sonos Amp. There is potentially the option to use another central tree about 8-10m from the sea which could mount facing the sea or back to the restaurant I can’t find any decent reviews of Sonance Outdoor online, and nothing to give a sense of volume available. I have 2 Era 300 which sound great so I’m presuming at least as good as those...It's a sit down restaurant (but lively) so music needs to be back ground music (people shouldn’t need to shout) with great sound quality, but with prolonged use - They will run for 14 hours per day every day.Now I see the thread about someone with repeated blown speakers and others recommend

Good Morning,I recently purchased a SONANCE MAG6.1 System w/ a Sonos AMP that I’m planning to setup in my back yard / patio area. I’m having trouble with deciding on the best placement for the 6 speakers+sub.I was leaning towards just covering the patio area, but may also consider covering some of the other back yard areas as well. With only one AMP in my configuration, however, it seemed like that may not be ideal in terms of adjusting volumes for the different areas of the yard.Would appreciate any advice you have. Please ignore all the brown grass in the photo - just had lawn irrigation installed a few weeks ago.  

I have a lot of older Sonos Speakers and a couple of newer ones. One newer one is a PORT which I downgraded to make it S1 compatable. Anyway I would now like to make the PORT S2 as I only use it on my HiFi and do not stream it to other devices. So I have managed to remove 2 Play 5s from my S1 app as part of the upgrade process but now I want to put them back. The SOnoS 1 app says I need to update so I cannot. The S2 app says devices incompatable or something. What is the quickest way to get my Port on S2 and all other devices back in S1. I seem to be stuck in a loop at the moment.

I have 2 Sonos Amps. One powers deck speakers (irrelevant, I think). The other powers Sonance 6.1 outdoor speakers around my pool. Both Amps are located inside my house. I am trying to figure out how to output audio through the pool speakers if I were to add an outdoor TV/projector. I really don’t want to drill more holes and bury more cable. Are there any good wireless solutions? I do have lots of access to power around the pool area, if that makes any difference at all. Otherwise, the amp is approx 35ft to first speaker and at least 50 feet or more from where I would place the video source. As another note, I live in a high humidity/high moisture/hot climate in the summer, so I opted not to use a “weatherproof” box to house the amp by the pool. TIA

Hello, I searched but couldn't get exact clarification on this specifically.  I have two DVC Episode 8ohm Rock speakers at a new home were moving to.  I have 1 AMP and know that the minimum impedance it can handle is 4ohm.  To maximize the DVC speakers safely with the AMP, what would be the best wiring scenario. Two wires are red/black and two are green/white connected to each speaker. Thanks!

I am planning my kitchen and dining room.  I am installing 2 sets of in-cieling sonos speakers in my kitchen and the adjacent dining room I wanted to put in-wall speaker/s.  My question is do I need to put a pair of in wall speakers (3rd in parallel series) or can I just put one in in-wall speaker?  the room only requires one speaker based on size, but not sure that I could do 3 on the right and 2 on the left and everything would function well.Thanks

I have a large Sonos system (19 devices).  I have purchased another 10+ devices in the past but upgraded them.  So needless to say I know my Sonos.I have had a problem with a Ghost TV  as the main imput into two of my rooms that only have amp(s).  A while go I factory reset all of my devices and everythign was working great.   Then one day I choose to expand the TV to these other rooms.   I have not been able to remove the Ghost TV since then.  L2 has even replaced one of my amps.    The good thing is that after 9 months I think I know the fix.  I have to factory reset all of my devices (2+ hours) to get rid of the Ghost TV, and never expand the TV into those rooms again.    The problem with the Ghost TV is that those rooms become surrond sound speakers only.    NO - I will not talk to support desk any more.   Hours upon hours to get to support desk to go now where  - you guys are painful.   Enough with varify my phone number, email etc…..Every time - Every transfer after 20 min of let

Has anyone used  The Sonos Large Round Flex Bracket (model LRDFBWW1) is specifically designed for the Sonos 8” In-Ceiling Speakers by Sonance (INCL8WW1). This bracket facilitates precise speaker placement during new construction or remodeling, ensuring optimal sound performance. They are said to be  Adaptable ABS Design: Provides durability and flexibility during installation. Snap-On Mesh Metal Wings: Allow secure mounting on joists, accommodating up to 24-inch (610mm) on-center installations. Pre-Installation Aid: Assists in marking speaker locations before drywall installation, ensuring consistent speaker alignment. 

Hi I just moved into a new house and it came with a 2009 Speakercraft audio home system. The wires are 16 gauge and i believe it is an mzc 66 system. I bought a Sonos Amp and am trying to connect it to the speakercraft connector which is a 16bit plug covered in plastic.After calling a local professional who analyzed the photos I gave him, I was told that I need a Niles 4 room speaker selector in order to get it working. I was wondering if that is the only alternative and if so how would a 16bit plug connect to it? I’m new to Audio technology so any insight would be great appreciated.

Hi,I’ve got three Sonos systems, two with the new Amp using the latest Sonos controller and one I was continuing to use my old Connect:Amp. When I tried to turn on my connect:amp after 9 months it boots up ok but I couldn’t see it in the S1 app. So I reset the amp, now Sonos S1 app doesn’t find it - it’s plugged directly into my router, I’ve reset the amp device and it’s flashing green light so looks ready to add. Any advice much appreciated!

I long ago sold my Bridge and my Sonos S2 app no longer show the device.  However, the sonos.com list of equipment still show it along with two controllers.  I only ever had one and also sold it.  How do I remove that equipment from my sonos.com system list?

I use Sonos Port to blend my Yamaha R N303 network receiver and stereo PSB MK ii speakers. the Port blends the PSB speakers with 2 Sonos play 5 and a Move speaker. I use IPhone 13 and IPad to interface with Spotify and Sonos app. 90% of the time I adjust volume within the Sonos app. I have to adjust the Receiver volume up to 65%-85% and also the sonus PSB volume considerably higher than the play 5s and move. this afternoon I hooked up  2 mordant Short outside wired deck speakers as B on the Yamaha. This also presents a very low volumes .  To get a decent loud volume on either the PSB or deck speakers I have to turn the receiver up high as well as adjust the port to high volumes well above the Sonos speakers in the app. I’m very uncomfortable with this for fear of a glitch blowing both sets of speakers or other damage. How should the port volume work. If the 3 Sonos speakers are at 40- Should the PSB speakers also be at 40?