Components & Architectural

I'm using a Sonos Bridge that is connected to my network via an ethernet cable. My Sonos Connect used to work fine over the SonosWireless(mesh) network, but after a firmware update, the Connect started behaving strangely - I now can't use it unless it's connected via ethernet cable. My other devices (Play 1, Play 3) are working fine over the mesh network. The only way I can get my Connect to work is by having a hard wired ethernet connection in. I have uploaded diagnostic information: 8263225 Any advice would be greatly appreciated! Thanks

I don't have sonos but would like to use it as part of a smart home system. I'm curious if it would be possible to have sonos linked to motion sensors. Therefore as you walk theough your house the music moves with you. It turns off when you leave the room and continues in the next room or hallway you enter.

I’m looking @ purchasing a new Sonos Connect Amp. How do I know if I am getting the latest model? I have seen different colored retail packaging as well as two different colors (blue & grey) used on the rear section of the amp where the connections are made. Thanks Chris

Will the Sonos app support Samsung Bixby voice control

I have a connect amp and a play 1. Can I somehow connect these to my smart TV so that the audio from my TV plays through my play 1? If so, how?

I got the Sonos Connect and this record player: https://www.amazon.com/Crosley-C100A-SI-Turntable-Adjustable-Counterweight/dp/B016OVYIK6 I have it all hooked up and set with line out (pre amp), but while I can hear a little sound from the record player, no audio is going into the Sonos connect. What am I doing wrong?

My ZP90 appears to not be working. The controller can't 'find' it. No lights appear on the Front even though power is connected. At the rear there are flashing yellow and green lights around the input connectors. It is connected to my Home Cinema System and previously worked perfectly. Anybody Help please?

I'm connecting my Sonos Connect to a Yamaha RX A-730 Home Theater receiver via either TosLink optical or Coax digital cable. Either one works fairly well, but I have to have the volume on my Yamaha turned almost to MAX. So I'm thinking I need some sort of pre-amp. Can anyone recommend a digital to digital (either toslink or coax) preamp to install between my Sonos Connect and my receiver ?? Thank you, JH

Does the in-App volume control work on the Connect's digital outputs? I want to connect the Connect's digital output directly to a pair of power amps via a 3rd party DAC which has no analogue volume control.

Hello! I like to be waiting for the integration of google home and sonos, however was thinking if there is an integration with harmony I can use in the short term? Thanks!

Hi - I just plugged my Connect AMP into a 240V mains plug without sliding across the voltage switch on the amp. There was a popping sound and it now doesn’t turn on. Has anyone has this happen and found the fix? I’m hoping I haven’t busted it Thank you

Have Boost set up in house now. Adding a Connect to outside BBQ area. Closest Sonos device I will have is an existing Connect in Family Room about 60 ft away. Will my new Connect I add to outside BBQ be able to connect via the mesh to the Family Room Connect or is that to far? if it does not reach will adding 2nd boost next to the Connect in the family Room send a stronger signal than existing Connect that is there? If i hook up 2nd Boost it will not be hardwired in, can it just connect to the mesh to extend signal assuming the Boost will extend further than a Connect and not have to be hardwired to network?

How can I set up a record player to a Sonos Sound bar? Can I or should i us a Sonos CONNECT. Thank-you

Hi, I hope I'm posting to the correct place but I cannot easily see how to contact customer support directly. I have just bought an Amazon Echo Dot and tried connecting it to the line-in input of my ZP90 but I cannot select the line-in as an input anywhere in the Sonos app. Even when I go into Settings->Room Settings there is no line-in option as there is for my other CONNECT amps. I have tried a different cable but this makes no difference. Can anyone help ?

I want to install 5 in-ceiling speakers(1 zone) and connect them with Sonos Connect AMP. Would it be possible to do so? Here is my product list; 250ft 12 awg cl2 speaker wire 5* Micca m-8c in-ceiling speakers 8ohm 100watt max/each Any help will be highly appreciated!

How would you connect an Audio Technica AT-LP120 record player? I tried to connect directly to Play 5 and can't get it to play.

New connect:amp problem - I just bought it brand new and it doesn't turn on. Plug it in and nothing, no light. I tried both wattage options also - any ideas?

What is the feature “placement adjustment” under the category sub setup? Thanks.

Hi all. I tried searching a bit, but haven’t found a direct answer to my question. I currently have a Connect hooked up by optical to my Denon. I can play anything through the Sonos controller just fine. I’m wondering how I get my TV sound currently running through the Denon back out to the Sonos in other room. I know I need a line out on the Denon to go to the line in on the Sonos. On the back of my receiver I have an Out and a Pre Out. The Out is labeled DVR and the Pre Out is labeled Zone2 for adding other zones with the Denon. I’ve tried running through the DVR portion and setting the line in on the Connect, but I can’t get TV sound to other zones. I read somewhere that people were using Zone2 Out, but then skimmed an article where someone said not to as it could damage the Connect. Can someone shed some light on what is needed? Thanks! Sam

The Line In on one of my Connect Amps, to which a Dot is wired, is set to Autoplay. With grouped speakers also checked. It works fine except when switching back to the Dot after music play via the app. Not only will the wired to Line In Dot not override music playing when given a voice command, music play does not start via the Dot even after the earlier music play is stopped using the app. And even after the queue is cleared via the app. When I pulled out the audio wire from the Dot, music was playing, heard via its speaker in response to the command it had received; plugged the wire back, but no music play. It took pressing the start/stop button on the Connect Amp and three flashes of the green light before music from the wired Dot started. There is no trouble in the reverse direction, in starting music from the app after the Dot is commanded to stop. Is this normal? Should the Line In set to Autoplay not respond to a signal as soon as it gets it? PS: The Dot signal levels also s

Hi, just got my Amp up and running and it's working but no sound from my sub. Any ideas what I may have done wrong? Needless to say the sub is plugged in, switched on and hooked up to the subwoofer port on the Amp. Thanks!

Hello all, I have a Marantz SR7012 and want to use all my sonos units throughout Home to play what’s coming from receiver, via TV, video games and even music station from receiver. I have the connect unit with my receiver and need to know what output from receiver to input from connect unit. Once I know what output to use, I would need to know if any special settings within receiver, if applicable. I already have it working the other way, to hear music play through all surround speakers by hooking to receiver input CD. Thanks

I currently am using the line in on my CONNECT but not the line out. Is it possible to hid the CONNECT from room listings (except in settings, of course) so that it doesn't show up as a room selection in the app?

Is the Bridge no longer necessary? If I recently installed a new AC router, should I take my bridge off-line?

Hi All, I already have a sonos connect amp powering some in ceilings, as well as a play 1. I now want to use an AV receiver with a SONOS connect and have a few questions: When I hit play on the connect amp, there is no turning the system on (its auto sensing)...I just hit play pn the app and it plays. If I'm using an AV receiver though, won't I have to switch the source to wherever the SONOS connect is plugged into.....as well as making sure the AV receiver is always on (or manually turning it on each time I want to use it which is not 'clean'). Is there a way around this or am I just incorrect? Also...I though I read about an AV receiver that basically had the connect built into it? Does this exist? Thanks all!