How to set up Sonos on a Tenda Mesh system (with or without a Boost)

Is the PC wired or wireless? If the former then the wired Sonos node should perform flawlessly.

It’s wired.

So, I have now wired the Kitchen speaker, and this is connected to the Hallway speaker (with the Dining Room and Living Room stereo pairs disconnected) and has been working without dropouts all day. I then decided to add the Dining Room pair and this seemed to be working OK without dropping out.

I then tried the Living Room pair and with these connected the system became unstable, with the Living Room speakers dropping in and out, but with the rest OK.

So, there is some progress!

Spoke too soon - dropping out again today, even with the reduced network.

You say you wired the Kitchen speaker. To what? If it’s to a Tenda node that’s presumably wireless. If the kitchen speaker then gives trouble it’s the Tenda connection that’s the most likely culprit. 

It strikes me that you need to break down the signal path, to isolate where things are going wrong.

The connection was by ethernet cable between the Kitchen speaker and the nearest node (about 1 metre away). The Hallway and Dining Room speakers were wireless.

I am now trying connecting the left speaker of the Dining Room stereo pair to a Tenda node by ethernet and seeing what happens with no other speakers active (other than the Dining Room right) . I will then gradually add in speakers until the dropouts begin again.

Just a short note of thanks to all the contributors, especially Ratty and Buzz, who have provided so much help in trying to deal with the issues here - thank you so much guys.

I have reached the end of the road with Sonos, and am in the process of disposing of my system, which has never worked satisfactorily in 3 years.

Thanks again!

That’s a disappointment. I’m not convinced the root cause was fully identified. It could easily have been the fact that, at least in a couple of scenarios, you’ve been relying on the Tenda mesh to interconnect the Sonos units. 

BTW did you ever try Ethernet-over-powerline? Although not officially supported by Sonos it can in some situations be the magic solution.

Hi Ratty - I have removed all but 2 of the speakers (Kitchen and Hallway) and the system seems much more stable. It is running OK at the moment and my wife can have music while she cooks dinner!

I didn’t get around to trying ethernet with powerline.

Thank you again for your patience and help.

Hi @Snakeplex 

Thanks for your post!

I’ve been reviewing this thread and see no mention of using WiFi instead of SonosNet - I presume this is something you’ve tried since installing the Tenda system? Your mesh nodes all seem to be on the same channel, and that’s a bonus.

If not, please go to Settings » System » Network » Manage Networks » Update Networks in the app (with all units on and present in the app) and connect Sonos to your mesh WiFi. When completed, remove all ethernet connections to Sonos and remove the Boost from power.

Also, although it was mentioned a couple of times by the fantastic crew you have helping you here, it wasn't really emphasised that the Sonos room with which you start a group (Group Coordinator) can be a very important choice - especially when things are on the cusp of working or not. With your home’s construction and the high bitrate of FLAC, you happen to be demanding just about the most anyone can demand from a Sonos system - without having around 30 devices, that is. The first room selected before grouping, when using SonosNet and in your particular situation, should be a wired unit. Though I do side with the opinion that Sonos should ideally not be wired to secondary mesh nodes, so that would leave Study as your only wired option.

If you try the WiFi-only option with no Sonos products wired, the ideal Group Coordinator would be a speaker with a good connection to the primary mesh node.

Working from the layout of your system that you posted back before you reduced the number of speakers on your system, I would have suggested wiring only the Study speaker but trying variations of it’s location in that room, and of the other speakers in theirs, looking to minimise the fraction of a straight line between any two units that is inside of a wall (diagonals through walls are worse than perpendicular paths, as they add to the thickness a WiFi signal passes through), while also keeping them as far away from the mesh nodes as you can.  An indication of where your mesh nodes are would be handy as I spotted at least 5 of them in an older diagnostic of yours - they should be kept at least 1m away from any WiFi device you’d like to work well.

I appreciate that you may have lost your patience after 2 years, but if you ever feel like giving things another go, please recreate your full system, test playback the way you’d like it to perform, submit a support diagnostic, reply here with the number given and @ me in the post (as I have you at the start of my post), and I’ll be happy to take a look for you. It might be, however, that you will only ever be able to play FLACs to smaller groups of speakers - grouping to them all may, in your particular case, require a lowering of bitrate, i.e. use 320Kbps mp3/wma/m4a instead of 1536Kbps FLAC - as you can see, the bandwidth requirement is almost 5x higher with FLAC.

I hope this helps.