Skip to main content
Contributor I
Jul 4, 2022 10:25 PM UTC
Answered

Arc or in-wall for fronts?

I’m building a new home and I have the opportunity to run with one of two options.  The room is fairly large with priority on home theatre, but to also play music in games room behind.  I’m looking for feedback on sound quality and ease of use.  Latency issues drive me mad btw!

OP1: Arc in front, Sonos amp + ceiling rears, Sonos sub

OP2: TV connected to one amp driving in-wall speakers on the sides of the TV, and a second amp driving ceiling rears, Sonos sub

I am hoping to be able to simply turn on Sony TV and go (with full surround sound) without turning on other devices and messing with surround settings.  Also, to use iOS to play music in the room with a stereo channel (ceiling speakers are used as L/R and not surround channel).

Thank you!

This topic has been closed for further comments. You can use the search bar to find a similar topic, or create a new one by clicking Create Topic at the top of the page.
buzz
buzzAnswer
Grand Maestro
Jul 5, 2022 4:19 AM UTC

With AMP or ARC up front and you ‘Bond’ the AMP driven ceiling speakers as surrounds, you will not be able to quickly pull the rears out of the surround system to be used as a stereo pair. It’s possible, of course, but this requires some fussing. SUB will be attached to the front speakers. It will require more fussing to reassign it to the rears while you use them as the only stereo speakers.

If the in-wall front speakers are relatively close to the TV, center channel is redundant. If they are some distance from the screen, or image poorly, you will usually experience a “hole in the middle” that would have been filled by ARC.

I don’t recommend attempting to “jam” through the SONOS system. Certainly, you can play tracks, but you’ll bump into latency issues if you attempt to incorporate a microphone. Note that ARC does not offer a Line-In. AMP has a Line-In, but Line-In is disabled when AMP is used as a surround amplifier.

14 replies

buzz
Grand Maestro
Jul 6, 2022 4:38 AM UTC

#1. You will have two sets of speakers attached to AMP. This will not be surround sound, you’ll have the same output from both pairs of speakers. You should have in-line speaker Volume controls to balance the levels. You’ll have the ‘A’/’B’ listener disagreement about delay, depending on listener location, but it will be on the order of 30ms and this may or may not matter to you. 30 feet between AMP and TV is not a big deal for audio. Use good quality cables. 

#2. Same comment as #1. I’m being a little pedantic, but I don’t think that you should consider the two sets of speakers as separate “zones”. We normally think of “zones” as being able to play separate content.

#3. The ONE(s) will be in the 75ms bin and AMP, if you use HDMI or Optical will be in the 30ms bin. If you use AMP’s Line-In for the TV audio, it will be in the 75ms bin. AMP and ONE(s) will be separate zones. In SONOS lingo you would “Group” the “Rooms” to play the same material and the Rooms would be time aligned with each other. (subject to the listener’s physical location, of course) When playing music AMP will always be in the 75ms bin.

Things are a bit slippery when using HDMI/Optical for the TV to AMP connection because there is an adjustment you can use to increase the latency to be very close to 75ms -- at the expense of lip sync.

#4. If you want true surround for the TV, you’ll need a second AMP for the rear speakers or you could use a pair of ONE’s or FIVE’s. Trueplay can tinker with things somewhat in an attempt to optimize the favorite TV viewing seat.

Translate
dmitchAuthor
Contributor I
Jul 6, 2022 5:24 AM UTC

@buzz thanks I’m learning a lot here.  So all Sonos users simply need to deal with the 30ms latency at the source, which would typically be either a soundbar or an amp. This must not be very noticeable otherwise complaints would be widespread. Any grouped device (another amp or satellite pair of sonos speakers) adds another 75ms so they would be playing 105ms behind the tv picture.

For my application, it seems that using a single Amp with two pairs of standard in wall/ceiling speakers is the value point.  The single grouping will play at the same 30ms delay, and I doubt any listeners will detect a difference (I have this setup right now with older non sonos equipment). 
 

One thing that you have mentioned twice now and that is “if” I connect tv to Sonos device through HDMI or optical. In what other way would I connect?

Translate
buzz
Grand Maestro
Jul 6, 2022 2:02 PM UTC

No, you will not have a 105ms latency. If you are playing audio from an HDMI video source through a soundbar or AMP, the latency will be 30ms for those speakers. If you simultaneously Group another player with this source, all members of the Group will be time aligned at 75ms. Depending on which speaker you are near, the latency will be 30ms or 75ms. Unless you are able to simultaneously able to hear speakers from both audio chains, this difference is usually not significant -- unless you attempt to provide lip sync audio to a remote monitor via a Grouped player.

Translate
buzz
Grand Maestro
Jul 6, 2022 2:29 PM UTC

The latency is added by the SONOS network transport services as a hedge to allow recovery from network communication issues before there are audio consequences. Data over a network is sent in “packets”. If a packet is delayed or lost the audio will suffer unless there is enough time for the packet to be resent before the player runs out of data. For a soundbar there is typically no network connection  (wired or wireless) between the TV and the audio system. Plus, a long latency here would impact lip sync significantly. Because there may be network supported surround speakers and SUB’s, some latency is prudent, but since surround speakers are typically in the same room as the front speakers, reducing the latency to 30ms is relatively low risk. In most cases a private, local 5GHz connection is used between the front and surround speakers. This connection is not visible to a regular WiFi user.

Translate