Skip to main content
Apr 24, 2016 10:20 AM UTC

Play unit power delivery question

Sonos does not specify this and I can understand why - what matter with play units is how loud they can go without clipping/distorting. But Sonos does not specify this either.

It would be interesting to know how the units stack up on clean sound levels delivered when compared to the 55 wpc Connect Amp, driving a typical HiFi speaker of, say 87dBm sensitivity levels. Has anyone done this comparison between the Connect Amp on one hand and play units on the other?

My experience is that even the 1 units go louder faster than a Connect Amp powered set up does. I haven't the place or the means where I can do this comparison with both running at 100% volume. Has anyone any useful experience to offer in this area? I have no idea of the sensitivity levels on the play 1 drivers, but my limited experience suggests that the 1 has amps that deliver more than 55 watts rms power. If I am not far wrong, that is impressive power delivery performance from the built in amps.
    This topic has been closed for further comments. You can use the search bar to find a similar topic, or create a new one by clicking Create Topic at the top of the page.

    25 replies

    jgatie
    Apr 26, 2016 11:55 PM UTC
    In all honesty, Amazon has solved the problem of background music or dialog interfering with the proper functioning of Alexa Voice. It's not flawless, but it's 98% there. It is really amazing in its ability to filter out background voices and hear commands over even loud music. The only time I see it fail every time is when Alex Baldwin says "Alexa" on the Echo TV commercials. She always wakes up to Alec.
    Translate
    KumarAuthor
    Apr 27, 2016 1:46 AM UTC
    Good to know. Still remains a perhaps good to have thing for me, I can't see myself pining for microphone equipped speakers.

    I suspect Alec Baldwin still has that effect on more than just Alexa.
    Translate
    chicks
    Apr 27, 2016 2:31 AM UTC
    suggests that the 1 has amps that deliver more than 55 watts rms power. If I am not far wrong, that is impressive power delivery performance from the built in amps.

    Remember that there is an amplifier per driver in the Play's, so it's not a direct comparison vs a 2- or 3-way speaker. A well designed passive crossover should have minimal losses, but the mid and/or tweeter will often be padded down to balance with the woofer. The Play series use DSP, splitting highs from lows before the power amp stages.

    One of the teardown sites mentioned that the Play:1 uses TPA-3116 Class D chips, each of which can very efficiency put 50W into a 4 ohm load if the DC supply is healthy enough. So, 50W+50W in the Play:1, max, though the tweeter will use far less power than the woofer.
    Translate
    KumarAuthor
    Apr 27, 2016 2:53 AM UTC
    Isn't that roughly the same then as the 110 wpc into 4 ohms from the Connect Amp? Quite impressive for the size and the price, if that be the case.
    Translate
    Ken_Griffiths
    Apr 27, 2016 8:59 AM UTC
    I thought this article by Robert Silva (Home Theatre Expert) was rather interesting, when it comes to talking about Amplifier Power Output ... It helps explain things in very simple terms.

    http://hometheater.about.com/cs/audiocomponents/a/aapowermada.htm

    Another article I read, also talks about the weight of speakers being useful.. These things need transformers to produce the watts and that means the more watts the heavier the transformer has to be (and the associated parts). Any speaker claiming a certain wattage output should have its spec. looked at very closely and not least 'picked up' to see just how heavy it is.

    Those little Play-1’s are rather heavy, aren't they?
    Translate
    Apr 27, 2016 9:07 AM UTC
    Another article I read, also talks about the weight of speakers being useful.. These things need transformers to produce the watts and that means the more watts the heavier the transformer has to be (and the associated parts). Any speaker claiming a certain wattage output should have its spec. looked at very closely and not least picked up to see just how heavy it is.

    Provided you're talking about active speakers yes, anyone trying to find a transformer in a passive speaker might be disappointed, it's the magnets that make up most of the weight in a passive speaker.
    Translate
    Ken_Griffiths
    Apr 27, 2016 9:16 AM UTC
    Another article I read, also talks about the weight of speakers being useful.. These things need transformers to produce the watts and that means the more watts the heavier the transformer has to be (and the associated parts). Any speaker claiming a certain wattage output should have its spec. looked at very closely and not least picked up to see just how heavy it is.

    Provided you're talking about active speakers yes, anyone trying to find a transformer in a passive speaker might be disappointed, it's the magnets that make up most of the weight in a passive speaker.


    Yes of course, thank you.
    Translate
    chicks
    Apr 27, 2016 2:55 PM UTC
    Sonos uses switching power supplies in all current products, so the power transformer can be tiny and lightweight. Only in linear supplies, where the transformer operates at 50/60 Hz, are they going to be heavy. Most pro amps these days (Crown, QSC, Behringer, etc) are also very lightweight for the same reasons: switching power supplies, class D amplifiers.
    Translate
    KumarAuthor
    Apr 28, 2016 1:17 AM UTC
    Right; I suspect the weight comes mostly from the magnets in the drive units and substantial casework. It does reinforce the quality feel of the unit of course.

    Digressing, I remember a review where it said that weight was one good way to distinguish between two amplifiers for quality, and it wasn't said tongue in cheek!
    Translate
    chicks
    Apr 28, 2016 2:38 AM UTC
    Probably the cleanest power amp ever, delivers enough power for 99% of home situations. Weight? 12.5 lbs.

    http://benchmarkmedia.com/products/benchmark-ahb2-power-amplifier
    Translate