Skip to main content
Contributor I
Jun 8, 2023 11:54 AM UTC
Answered

Update Error

Just bought a Move, going through the set up it tells me an update is required. Update keeps failing and I get error code 1013 suggesting I move the Move closer to the internet hub. They are sat right next to each other, couldn’t get any closer and yet I still get the error?

This topic has been closed for further comments. You can use the search bar to find a similar topic, or create a new one by clicking Create Topic at the top of the page.
JFRoyAnswer
Lyricist I
Jun 9, 2023 7:09 PM UTC

I turned off my speaker, turned it back on again and it was able to update. Go figure.

25 replies

JFRoyAnswer
Lyricist I
Jun 9, 2023 7:09 PM UTC

I turned off my speaker, turned it back on again and it was able to update. Go figure.

Translate
Lyricist I
Jun 9, 2023 7:18 PM UTC

I turned off my speaker, turned it back on again and it was able to update. Go figure.

Ha! Just did this and it worked. Never underestimate turning tech off and on again to solve problems. 

Translate
Lyricist I
Jun 9, 2023 7:25 PM UTC

Exactly the same issue:  new Move, error 103 updating :(

I have many other Sonos devices in the system, and never this issue before.

Translate
Airgetlam
Jun 9, 2023 7:26 PM UTC

Did you try the power cycle that seemed to be working for others?

Translate
Bruce
Lyricist I
Jun 9, 2023 7:33 PM UTC

Sorry, didn’t see that - YES, just powered down, powered back on and hit “try again,” and it worked.

Translate
AjTrek1
Jun 9, 2023 7:49 PM UTC

The power cycle a device is “fix-it 101” back to basics step which resolves a multitude of tech issues. My apologies to all for not mentioning that simple procedure in my post.

I’m also surprised that that simple step is not mentioned in the official Sonos link I provided 🤔. Maybe Sonos needs to get back to basics as well with sone  of their  trouble shooting steps. The only reason I can think of as to why the step is not mentioned is because power cycling a device may remove the root cause of the issue that Sonos tech support would need in a diagnostic.

In any event Kudos to @JFRoy for the solution. Well Done!

Translate
Together Everyone Achieves More = T.E.A.M.
Lyricist I
Jun 9, 2023 7:52 PM UTC

Power cycling is not working for me. I have done the on/off thing well over 20 times, but doesn’t seem to make any difference. i’ve also done a factory reset on the device.

Firmware update fails every time,

Translate
Airgetlam
Jun 9, 2023 8:55 PM UTC

It may be a separate issue, manifesting in the same end error, the challenge of many network issues, that look similar, but aren’t . 

I would recommend that you submit a system diagnostic within 10 minutes of experiencing this problem, and call Sonos Support to discuss it.

There may be information included in the diagnostic that will help Sonos pinpoint the issue and help you find a solution.

When you speak directly to the phone folks, they have tools at their disposal that will allow them to give you advice specific to your Sonos system and network.

Translate
Bruce
Contributor I
Jun 9, 2023 9:06 PM UTC

Same issue here with new Move speaker, tried the power cycle and the wifi channel, also tried tirning off the 5Ghz as sonos suggested, still no good. Must be a bad batch of speakers given everyone suffering?

Assume a system diagnostic wont help as the speaker is not connected to the wifi yet, bad/no connection to wifi is preventing speakers access to sonos update server. 

Translate
Airgetlam
Jun 9, 2023 9:09 PM UTC

Still worth calling in, though. And if you have other speakers in your system, a diagnostic should be available, and might help them pin down why you’re unable to update that one speaker. 

Translate
Bruce