Skip to main content
Contributor I
Dec 22, 2020 9:52 AM UTC

Mixed network with Sonos Beam, One and Move

Hi,

I have a Beam connected to ethernet. When the Beam and my Sonos One are the only devices turned on, the Sonos One automatically joins Sonosnet via wireless, all good. But as soon as my Move is turned on, the Sonos One switches to Wifi (WM:1). The Beam is on my Living Room while the Sonos One and Move are near each other in my Bedroom.

 

Is it possible for Sonos One to join the Sonosnet when it's near a Move? I know the Move doesn't support Sonosnet, but I don't understand why the One also needs to be in Wifi.

This topic has been closed for further comments. You can use the search bar to find a similar topic, or create a new one by clicking Create Topic at the top of the page.

19 replies

106rallye
Dec 22, 2020 10:23 AM UTC

Though it seems strange behaviour, my first question is would be if the One workslike it does on Sonosnetwhen it switches over to wifi. If it does, why bother?

Translate
azeeAuthor
Contributor I
Dec 22, 2020 10:28 AM UTC

Well, it does. But then what's the benefit of having the Beam connected to Ethernet? If I can't make it work, I'm better off freeing that router port to connect another device 😅.

Translate
ratty
Dec 22, 2020 11:51 AM UTC

This does seem a little strange, unless Sonos has become clever enough to figure that two adjacent units which might be grouped are better off on the same channel. If so, it’s not something I’ve seen before.

A more obvious explanation could be that the One has a borderline SonosNet signal and reverts to a better WiFi signal. We’d need a bit more info to test this idea. Get the One onto SonosNet then go to http://x.x.x.x:1400/support/review (where x.x.x.x is the IP address of the Beam, from About My System) and screenshot the Network Matrix.

Translate
Ken_Griffiths
Dec 22, 2020 12:27 PM UTC

azee,
I would first reset/remove any WiFi credentials that maybe stored in the area of the Sonos App under “Settings/System/Network/Wireless Setup” these are not required when your main speakers are running on SonosNet and just to add this has no bearing on the ‘Move’s’ WiFi connection.


You might also want to go onto try this (if necessary):

If the Move is perhaps operating on the 2.4ghz WiFi band in this case  -  you could consider factory resetting it and then setting it up on the 5ghz band instead and see if that helps to also stop the problem. There are other ways to achieve the same outcome, but factory resetting is perhaps the easier method.

 

Also note you will still have the 2.4ghz credentials showing in the Sonos App’s network settings under ‘Networks Not in Use’ It pays to also remove the 2.4ghz credentials from there. I find there is ‘less chance’ of the SonosNet connected speakers dropping back to a 5ghz WiFi signal.

 

 

Translate
ratty
Dec 22, 2020 12:31 PM UTC

Shoving the Move onto 5GHz is definitely a possibility, but I’m still curious as to why the One is falling through onto WiFi.

Translate
azeeAuthor
Contributor I
Dec 22, 2020 3:05 PM UTC

Ok, so I don't know exactly what happened, but I couldn't get the One to join Sonosnet again even with the Move turned off. I ended up resetting the network settings in the app so it could join it. Even after resetting the network settings, as soon as the Move is turned on, the One shows as WM: 1.

Here's the Network Matrix with just the Beam and the One, both on Sonosnet:

And here's the same with all devices, Beam (Family Room) in the Sonosnet, the others over Wifi:

 

Switching the Move to 5Ghz would mean I need to have different SSIDS for the 5Gh and 2.4Ghz networks?

Translate
ratty
Dec 22, 2020 3:08 PM UTC

According to the network matrix the Bedroom player is not on SonosNet.

Translate
azeeAuthor
Contributor I
Dec 22, 2020 3:14 PM UTC

Hmm, let me try once again, app was showing WM: 0. How do I figure this out from the screenshot above? (Or any other place in the support/review link?).

Translate
ratty
Dec 22, 2020 3:16 PM UTC
  1. There should be data in the squares where Family Room and Bedroom intersect.
  2. In the left column the Bedroom should say “Secondary Node” below the room name.

Have you disabled the “WiFi” (i.e. SonosNet) on the Beam? Try re-enabling it...

Translate
azeeAuthor
Contributor I
Dec 22, 2020 3:19 PM UTC

Ok, so… app shows WM: 0 for One, but Network Matrix is almost the same (changes are: Noise Floor: -107, -108, -108 and OFDM ANI level: 3), it doesn't show Secondary or no data in the intersection.

Translate