Skip to main content
Avid Contributor I
Sep 27, 2022 6:37 PM UTC
Answered

Direct connection between Sonos Arc and Sub Gen 3?

I recently bought Sonos Arc + Sub Gen 3. I was wondering if there is a way Sonos Arc can connect directly with Sub Gen 3 (without being depedent on WiFi). Similar to how Samsung Q950A or JBL Bar 9.1 does.

This topic has been closed for further comments. You can use the search bar to find a similar topic, or create a new one by clicking Create Topic at the top of the page.
ratty
rattyAnswer
Sep 28, 2022 4:08 PM UTC

If the question is “what if the router dies?” then it’s possible that the Arc+Sub will continue to operate for TV audio only, at least for a while, using their existing IP addresses.

When the IP leases expire the situation could become unpredictable. The units may then operate in AutoIP/APIPA mode, but you’d be in completely unsupported territory.

You can of course try this for yourself by powering off your router.

18 replies

ratty
rattyAnswer
Sep 28, 2022 4:08 PM UTC

If the question is “what if the router dies?” then it’s possible that the Arc+Sub will continue to operate for TV audio only, at least for a while, using their existing IP addresses.

When the IP leases expire the situation could become unpredictable. The units may then operate in AutoIP/APIPA mode, but you’d be in completely unsupported territory.

You can of course try this for yourself by powering off your router.

Translate
Avid Contributor I
Sep 28, 2022 4:17 PM UTC

“what if the router dies?” 

 

may be this is the question I should have started with :) Thanks for that. Tomorrow, I am going to try turning the router off and see what happens. I already tried this with Arc (standalone) and it worked well as far as playing audio from the TV is concerned. Will try with Arc+Sub combination.

Translate
ratty
Sep 28, 2022 4:20 PM UTC

The router would typically lease IP addresses for 24 hours. After 12 hours therefore the units would attempt to renew the lease.

You’d probably need to leave the router off for 24+ hours to see what really happens between the Arc and Sub.

Translate
Avid Contributor I
Sep 28, 2022 4:30 PM UTC

Thanks for that tip

Translate
Avid Contributor I
Oct 1, 2022 3:40 PM UTC

@ratty had a little bit of luck. It’s possible to use Arc ‘out-of-box’. Just unbox it, power it on, connect to the TV with eArc and it’s good to go. No need for the S2 app, local network, or internet. TV will control the volume via eArc. of course, connecting Sub will not be possible. Will move this to a separate thread. 

Translate
ratty
Oct 1, 2022 5:13 PM UTC

I’m not sure you’re correct, and one could only verify by factory reset (which I’m not about to do).

As far as I can recall Sonos home theatre products won’t play TV input until part way through the app’s setup process.

Translate
Avid Contributor I
Oct 1, 2022 5:21 PM UTC

I’m not sure you’re correct, and one could only verify by factory reset (which I’m not about to do).

As far as I can recall Sonos home theatre products won’t play TV input until part way through the app’s setup process.

I did factory reset. Arc and Sub, both. I bought the system three days ago and it's my first Sonos system. So I didn't have anything to lose by factory resetting the whole thing. Arc worked without any set up (for the TV input). Didn't even have to take my phone out. 

Translate
ratty
Oct 1, 2022 5:25 PM UTC

I’m not sure you’re correct, and one could only verify by factory reset (which I’m not about to do).

As far as I can recall Sonos home theatre products won’t play TV input until part way through the app’s setup process.

I did factory reset. Arc and Sub, both. I bought the system three days ago and it's my first Sonos system. So I didn't have anything to lose by factory resetting the whole thing. Arc worked without any set up (for the TV input). Didn't even have to take my phone out. 

In that case I stand corrected.

Of course using the Arc as a dumb standalone soundbar, without internet access or software updates, is not what users do.

Translate