Skip to main content
Contributor I
Dec 25, 2013 2:06 PM UTC
Answered

Creating 5.1 with non-Sonos Subwoofer

Sub disabled when Setting up SONOS CONNECT:AMP as Surround Rears Why are you disabling the subwoofer out when configuring the Connect Amp to drive non-Sonos rear speakers with a Playbar? I have a my own sub that i want to connect to the Connect Amp so that it can be driven along with the rest of the system. I do not want to buy another Sonos sub. Surely this would just be a software or firmware update that is easily achievable.
This topic has been closed for further comments. You can use the search bar to find a similar topic, or create a new one by clicking Create Topic at the top of the page.
Chris
ChrisAnswer
Lead Maestro
Mar 14, 2018 2:05 AM UTC
It's not possible. A 5.1 system has a discrete .1 channel.

The Connect:Amp is only able to receive a stereo signal (R/L). In this case the R/L is the right and left surround sound. There is no dedicated chanel to send to the Subwoofer.

The original design of the Connect:Amp was not to be used in the manner of surrounds. Its original hardware takes a stereo signal. Filters it through a crossover - sending higher frequencies to left/right channel speakers and the lower range to the subwoofer output. So the subwoofer output sits between the stereo input and the speaker output (just as a normal sub would). There is no direct channel to the subwoofer just a processing of the stereo signal.

Therefore, there is no reason to have the subwoofer active. There is no reason to filter out the low end output from the surround sound mix (as the surround sound mix doesn't have the LFE channel or really any low end to speak of).

It is an internal hardware issue that makes it impossible for the Connect:Amp to pass a discrete LFE channel in the form of the .1 signal from a surround sound setup. It just physically is not built to do that - so no asking for it will solve the issue.

A new Connect:Amp model designed to pass a discrete signal would be required.

Hope this makes sense as Sonos has no way to add this ability to the current model.
Respect the Queue (2)Move (3)Beam (1) Era100 (2)ARC (1)SonosOne (1)Playbar (4)Play5 (4)Play1 (3)Play3 (1)Port (2)Connect (1) Roam (2) Ace (1)Connect:Amp (4)Sonos Amp (1)Sub + (9) Echo + Smartthings; (2)Play)

66 replies

Lyricist II
Dec 11, 2017 9:26 PM UTC
Add my vote to drive a third party sub. I'd even buy a connect:amp to drive the .1 channel and nothing else.
Translate
Lyricist I
Jan 5, 2018 4:45 PM UTC
Count me in to want third party sub support. C'mon, Sonos.
Translate
Lyricist II
Mar 13, 2018 9:38 PM UTC
Add me as well. We have a Playbar and Connect Amp in our Great Room and Connect Amp and Subwoofer in our kitchen which is basically the same room. I'd rather attach the sub to the Great Room Connect Amp rather than the Kitchen and Great room Grouped.
Translate
Chris
ChrisAnswer
Lead Maestro
Mar 14, 2018 2:05 AM UTC
It's not possible. A 5.1 system has a discrete .1 channel.

The Connect:Amp is only able to receive a stereo signal (R/L). In this case the R/L is the right and left surround sound. There is no dedicated chanel to send to the Subwoofer.

The original design of the Connect:Amp was not to be used in the manner of surrounds. Its original hardware takes a stereo signal. Filters it through a crossover - sending higher frequencies to left/right channel speakers and the lower range to the subwoofer output. So the subwoofer output sits between the stereo input and the speaker output (just as a normal sub would). There is no direct channel to the subwoofer just a processing of the stereo signal.

Therefore, there is no reason to have the subwoofer active. There is no reason to filter out the low end output from the surround sound mix (as the surround sound mix doesn't have the LFE channel or really any low end to speak of).

It is an internal hardware issue that makes it impossible for the Connect:Amp to pass a discrete LFE channel in the form of the .1 signal from a surround sound setup. It just physically is not built to do that - so no asking for it will solve the issue.

A new Connect:Amp model designed to pass a discrete signal would be required.

Hope this makes sense as Sonos has no way to add this ability to the current model.
Translate
Respect the Queue (2)Move (3)Beam (1) Era100 (2)ARC (1)SonosOne (1)Playbar (4)Play5 (4)Play1 (3)Play3 (1)Port (2)Connect (1) Roam (2) Ace (1)Connect:Amp (4)Sonos Amp (1)Sub + (9) Echo + Smartthings; (2)Play)
Lyricist I
Dec 5, 2018 2:10 AM UTC
hi Chris! I think I understand this answer you gave on COnnect:amp. If I proceed with a connect (non amp) and connect that either direct to my powered sub, or to a receiver that is connected to my sub, would that sort the channels correctly?
Translate
Chris
Lead Maestro
Dec 5, 2018 12:34 PM UTC
No. You have no way to get the .1 signal to a connect.
Translate
Respect the Queue (2)Move (3)Beam (1) Era100 (2)ARC (1)SonosOne (1)Playbar (4)Play5 (4)Play1 (3)Play3 (1)Port (2)Connect (1) Roam (2) Ace (1)Connect:Amp (4)Sonos Amp (1)Sub + (9) Echo + Smartthings; (2)Play)