Rollout of "Disable SonosNet" feature - completion date?

I’m in the US.  The feature is active on my Sonos app.  Not sure when it became active.  The only Ethernet connected Sonos device I have has had SonosNet disabled for quite a while now.

I do have a question about a global option to disable SonosNet.  What effect does that have on Bonded rooms?

You’d need to enter your router’s SSID, running non-wired units in WiFi mode.

​@LunchMunch - Very unlikely to be able to force it and as has been mentioned elsewhere it is on a device basis so geography does not really apply.

I am still waiting this rime around too and in the past it has been anything from immediately on update to around 2 months (and subsequent updates). It is a case of just being patient…

​@MoPac - As far as bonds go it should have no impact as long as Sonos knows your local Wi-Fi. Stereo pairs are on local network anyway and bonded surrounds/subs are on an 'invisible' network controlled by the sound bar/primary speaker... I think 🤔

I have it on my iPhone, but not iPad. It’s also on 2 of 3 android devices now.

So if I globally disabled SonosNet and that turned off SonosNet on my Arc that would have no effect on the 5GHz bonding wireless signal?  I have always read here that you should never disable SonosNet on a soundbar.

That is actually the purpose of implementing this. Being able to turn off SonosNet and still have wifi & bonding work properly. This is the old 2.4Ghz SonosNet being referred to. Not the new bonding invisible SonosNet that is being turned off. Just make sure all non ethernet devices are set up on wifi.

Edit: And I believe the advice was to not disable wifi on a soundbar. Even though it can be done if everything is on ethernet. Not really recommended.

​@MoPac My understanding too is that one should never disable Wi-Fi on a sound bar, or any non-hardwired speaker come to that.

As long as a speaker knows and is talking to your local network, either Wi-Fi or hardwired, then that should be fine.

However, if one does disable Wi-Fi on a soundbar, wired or not, then the satellite bonding will be lost... the bonding is maintained outside of and in addition to SonosNet.

SonosNet is just another Wi-Fi network independent of your local Wi-Fi and bonding so any speakers bonded, on your local network (hardwired or Wi-Fi) will not need or use SonosNet.

The advise for soundbars is to never disable the radio, not Sonosnet. If you disable the radio the soundbar can't communicate with subs or surrounds.

As that isn't confusing enough there are two Sonosnets that aren't anything alike, the one we are familiar with is the 2.4 gHz mesh used to communicate between devices when Wi-Fi isn't being used as a Sonos is wired to Ethernet. The second is the 5 gHz Sonosnet used to communicate with a soundbar's Subs and Surrounds.

And if your head isn't hurting yet... Sonos calls the "disable the radio" switch disable Wi-Fi. Technically correct as it does disable the Wi-Fi but is more like dealing with a split fingernail by cutting off the finger.

The disable Sonosnet option disables the 2.4 gHz Sonosnet while leaving the 5 gHz Sonosnet active. Giving you the ability to have your Sonosnet capable speakers stay on your Wi-Fi if you wire one to Ethernet, and to have your Sub and surrounds working.

The so-called “new SonosNet” has actually been around since 2013. It’s officially known as ‘Direct Routing,’ a feature of SonosNet that’s also built into WiFi mode.

It was recommended that you not disable WiFi, which is completely different from disabling Sonosnet.  Disabling WiFi turned off all WiFi radios, including the connection to surrounds and Subs.  DIsabling Sonosnet just disables Sonosnet, the WiFI radios are still on.