Skip to main content
jaytay68
Contributor I
April 6, 2025
Answered

6 x Sonance VP60R’s to a single Sonos Amp

  • April 6, 2025
  • 6 replies
  • 217 views

Hi all,

as title says really.  I’m currently in the process of a kitchen renovation and trying to understand whether or not I can wire 6 Sonance VP60Rs to a single Sonos amp ? 
 

All I can seem to find is the following 

“The Sonos Amp is designed to reliably power up to three pairs (six total) of Sonos Architectural by Sonance speakers (INCLGWW1) when wired in parallel”


I do have a second amp but was planning on using that exclusively for a pair of outdoor speakers.

 

Thanks in advance 

This topic has been closed for further comments. You can use the search bar to find a similar topic, or create a new one by clicking Create Topic at the top of the page.
Best answer by Corry P

Hi ​@jaytay68 

Welcome to the Sonos Community!

To expand upon ​@Airgetlam’s answer a little, if the speakers are not part of the Architectural line, then only 4 speakers are supported. I do believe, however, that Sonance sell some speaker sets along with a Sonos Amp - if your speakers were part of such a set, then they will likely be fine.

I hope this helps.

6 replies

Airgetlam
Airgetlam
April 6, 2025

Are these Sonance speakers part of the Architectural line, and labeled as such? What does the Sonance website say?

Bruce
Corry P
Corry PAnswer
Sonos Staff
April 10, 2025

Hi ​@jaytay68 

Welcome to the Sonos Community!

To expand upon ​@Airgetlam’s answer a little, if the speakers are not part of the Architectural line, then only 4 speakers are supported. I do believe, however, that Sonance sell some speaker sets along with a Sonos Amp - if your speakers were part of such a set, then they will likely be fine.

I hope this helps.

"Common sense is the collection of prejudices acquired by age eighteen." - Albert Einstein
    Billycanfly
    Contributor I
    April 22, 2025

    Is it possible to have two of the six speakers wiring run through a volume knob and then run to the Sonos amp?  I assume yes since all the knobs really do is cut off some of the power to the speaker.  That way the four other speakers could be in a living room and the other two (6 total) can wire through volume knobs and then to amp with other wires 

    Corry P
    Corry P
    Sonos Staff
    April 22, 2025

    Hi ​@Billycanfly 

    Is it possible? Sure.

    Is it a supported configuration? No, I don’t think so.

    Will it work? Probably, yes.

    If the Amp ever reduces the volume to 15%, however, it is doing so to protect itself from overloading - if this ever happens, I’d recommend removing the volume control from the equation.

    I hope this helps.

    "Common sense is the collection of prejudices acquired by age eighteen." - Albert Einstein
      bschuppe
      Lyricist I
      May 14, 2025

      A bit late here, but with some info that may help. Are you hooking up three speakers to the left channel, and three to the right channel amp outputs? If so, and if you’re hooking them up in parallel, if the speakers are 8 ohms, you’ll have an effective (speaker) load for each amp channel of 2.67 ohms. That is a TOUGH load for an amp to drive. A Crown or QSC amp (or other good commercial-grade amp)… no problem. A typical consumer-grade amp?… 4 ohms (two 8 ohm speakers in parallel) is asking a lot.

      And, just confirmed, Sonos does NOT recommend anything less than a 4 ohm (nominal) load.

        buzz
        buzz
        May 14, 2025

        Install a Niles VCS100K for each pair of speakers.

          Terms & ConditionsAccessibility statement